Free Engineering Tool · NFPA 92 / NFPA 101
Door Opening Force Calculator
Pressurized stairs and smoke control zones push on the doors people must open to escape. Enter the door size, closer force and pressure difference to get the opening force, check it against the limit, and find the largest pressure difference the door can take, using the method in NFPA 92 and the IBC.
- Based on NFPA 92 / NFPA 101
- Free, runs in your browser; your inputs stay on your device
- Screening tool, not reviewed or sealed by a licensed engineer
- Last updated October 2026
Screening tool, not engineering advice. This calculator estimates results with simplified published methods. It has not been reviewed or sealed by a licensed engineer for your project, and DGA does not warrant that its results are accurate, complete or suitable for any use. Check every result independently and have the licensed professional responsible for your project review it before you rely on it. Use is subject to the Terms of Use.
Advanced method. The correlations behind this tool come from research and test data with narrow ranges of validity. Outside those ranges results can be wrong by a wide margin, and they are no substitute for a fire model or an analysis by a qualified fire protection engineer.
Door
Pressure and Limits
The usual limit is 30 lbf (133 N) to set a means of egress door in motion, applied at the latch side (NFPA 101 and the IBC). Use the closer force measured with no pressure difference, or the closer data.
Result
Opening Force and Pressure Difference
About This Tool
A pressure difference across a closed side-hinged door acts over the whole leaf and resists anyone pushing from the low-pressure side. Treating the leaf as a beam hinged at one edge and pushed at the knob, the force needed to open it is the closer force plus the pressure force: F = Fdc + K W A Δp / [2 (W − d)], where W is the leaf width, A the leaf area, d the distance from the knob to the latch edge and Δp the pressure difference. K is 5.20 with force in lbf, lengths in ft, area in ft² and pressure in inches of water, and 1.0 in SI units (N, m, m², Pa). This is the equation in the NFPA 92 annex and IBC Section 909.6.2.
Solving the same equation for Δp gives the largest pressure difference that keeps the door at or under the force limit: Δpmax = 2 (Flimit − Fdc)(W − d) / (K W A). NFPA 101 and the IBC limit the force to set a means of egress door in motion to 30 lbf (133 N), applied at the latch side. The lower end of the design range is the minimum pressure difference NFPA 92 requires to hold smoke back: 0.05 in. of water in a sprinklered building, and 0.10 to 0.18 in. in a nonsprinklered building depending on ceiling height. The IBC stair pressurization option uses 0.10 to 0.35 in. with all doors closed. The calculator shows the workable range between the minimum and the force limit.
Worked example
A stair door is 36 in. wide and 84 in. tall (21 ft²), the knob is 3 in. from the latch edge and the closer takes 8 lbf. At 0.25 in. of water the pressure adds 5.20 × 3 × 21 × 0.25 / (2 × 2.75) = 14.9 lbf, for a total of 22.9 lbf, under the 30 lbf limit. The largest pressure difference for 30 lbf is 2 × 22 × 2.75 / (5.20 × 3 × 21) = 0.37 in. of water, so in a sprinklered building the stair can run anywhere from 0.05 to 0.37 in. A 12 lbf closer would cut the top of that range to 0.30 in.
Assumptions and limits
The equation covers a side-hinged swinging door with a uniform pressure difference, the force applied at the knob, and no hinge friction. It does not cover the separate 15 lbf limit to release the latch, sliding or power-operated doors, or doors held by wind. The pressure difference in a real stair varies with height, stack effect, wind and how many doors are open, so check the door at the highest pressure the system can produce, not only at the design point. Use the closer force measured with no pressure difference, or the closer data.
When to bring in an engineer
Balancing the minimum pressure difference against door forces is the core of a pressurization design, and tall or complicated buildings usually need a network model and field testing. DGA designs and reviews smoke control systems and supports commissioning and integrated testing of pressurized stairs.
References
- NFPA 92, Standard for Smoke Control Systems, National Fire Protection Association, 2024 edition: minimum design pressure differences across smoke barriers, maximum pressure difference set by door opening forces, and the door opening force method in the annex.
- NFPA 101, Life Safety Code, National Fire Protection Association, 2024 edition: door leaf operating forces for means of egress doors.
- International Code Council, International Building Code, 2024 edition: Section 909.6 (pressurization method and the door opening force equation), Section 909.20.5 (stair pressurization) and Section 1010.1.3 (door opening force).
- Klote, J.H., Milke, J.A., Turnbull, P.G., Kashef, A. and Ferreira, M.J., Handbook of Smoke Control Engineering, ASHRAE, Atlanta, 2012: door opening forces and design pressure differences for pressurization systems.
Frequently Asked Questions
What is the maximum door opening force for an exit door?
NFPA 101 and the IBC allow no more than 30 lbf (133 N) to set a means of egress door in motion and 15 lbf to open it to its full width, with the force applied at the latch side. With a smoke control system running, the pressure difference across the door counts toward that 30 lbf.
How do you calculate the maximum pressure difference across a door?
Rearrange the door opening force equation: the largest pressure difference is 2 times the force limit minus the closer force, times the width minus the knob distance, divided by K times the width times the door area. For a 36 by 84 in. door with an 8 lbf closer and a 3 in. knob offset, that is about 0.37 in. of water.
What is the minimum pressure difference for smoke control?
NFPA 92 requires at least 0.05 in. of water (about 12.4 Pa) across smoke barriers in a sprinklered building. In a nonsprinklered building the minimum rises with ceiling height, from 0.10 in. for a 9 ft ceiling to 0.18 in. for a 21 ft ceiling.
Why does a wider door need more force?
The pressure acts on the whole leaf, so the force grows with the door area, and the knob sits a fixed distance from the latch edge, so the lever arm does not grow as fast as the area. Double doors or narrower leaves reduce the force at the same pressure difference.
Related Tools and Services
More smoke control and tenability calculators →
Engineering aid only, provided as is and without warranty. Results depend on the inputs and on the simplifying assumptions of the method summarized on each tool page, and DGA has not verified them for your application. They do not replace code-required design, testing or review by the licensed engineer responsible for the project. Use of the tools is subject to the Terms of Use.
Related Reading
Articles from DGA Insights on the code and the method behind this calculator.