Free Engineering Tool · NFPA 92

Visibility in Smoke Calculator

Estimate how far occupants can see through fire smoke. Enter the smoke as an extinction coefficient, an optical density or a mass of fuel burned, and compare the visibility of exit signs, doors and walls with a tenability criterion.

  • Based on NFPA 92
  • Free, runs in your browser; your inputs stay on your device
  • Screening tool, not reviewed or sealed by a licensed engineer
  • Last updated October 2026

Screening tool, not engineering advice. This calculator estimates results with simplified published methods. It has not been reviewed or sealed by a licensed engineer for your project, and DGA does not warrant that its results are accurate, complete or suitable for any use. Check every result independently and have the licensed professional responsible for your project review it before you rely on it. Use is subject to the Terms of Use.

Advanced method. The correlations behind this tool come from research and test data with narrow ranges of validity. Outside those ranges results can be wrong by a wide margin, and they are no substitute for a fire model or an analysis by a qualified fire protection engineer.

Smoke Density

Visibility Criteria

NFPA 92 Annex M keeps an 8 to 3 ratio between sign and wall distances: an internally illuminated sign visible at 30 m (100 ft) goes with doors and walls visible at 11.25 m (37 ft).

Result

Light-emitting sign visible at
0
Doors, walls, reflecting signs
0
Extinction coefficient
0
Smoke limit for the criterion
0

Visibility Against Extinction Coefficient

Keep these results

About This Tool

Smoke particles absorb and scatter light, so the light that reaches an observer falls off exponentially with distance: I / I0 = e−σL, where σ is the extinction coefficient of the smoke. In smoke-filled corridor tests, Jin found that the distance at which a sign can just be made out is inversely proportional to σ: S = K / σ. K is about 8 for light-emitting (internally lit) signs and about 3 for reflecting signs, doors and walls, with measured ranges of roughly 5 to 10 and 2 to 4. NFPA 92 keeps the same 8 to 3 ratio in its tenability guidance.

Optical density uses base-10 logarithms, OD = log10(I0 / I) / L, so σ = ln 10 × OD = 2.303 × OD. Smoke detector sensitivity is often stated as percent obscuration per foot, 100 (1 − e−σ × 0.3048 m), which the calculator also reports. When the smoke is known by mass, σ = σm × Cs, where σm is the mass specific extinction coefficient. Mulholland and Croarkin measured 8.7 m2/g for smoke from flaming fires; older data give 7.6 m2/g for flaming and 4.4 m2/g for smoldering fires. For a fuel burned, Cs = ys × m / V: the soot yield times the mass burned, spread through the volume the smoke fills. Published soot yields run from about 0.01 g/g for well-ventilated wood fires to about 0.2 g/g for some plastics, so use a value measured for the actual fuel.

The criterion field sets the visibility required for doors and walls. A limit of 10 m (33 ft) is common in performance-based design. NFPA 92 Annex M asks that a sign lit at 80 lx be discernible at 30 m (100 ft) and doors and walls at 11.25 m (37 ft). Shorter distances, such as 5 m (16 ft), are sometimes accepted for small rooms that occupants know well. The calculator gives the densest smoke that still meets the chosen distance, σmax = K / S, and the matching smoke concentration.

Worked example

A fire in an atrium burns 2 lb (0.91 kg) of upholstered furniture with a soot yield of 0.10, and the smoke mixes through 100,000 ft3 (2,832 m3). The smoke concentration is 0.10 × 907 g / 2,832 m3 = 0.032 g/m3, and σ = 8.7 × 0.032 = 0.279 per m (0.085 per ft). An exit sign is visible at 8 / 0.279 = 28.7 m (94 ft) and doors and walls at 3 / 0.279 = 10.8 m (35 ft), so the 10 m (33 ft) criterion is just met. Twice the fuel burned would halve both distances and fail the criterion.

Assumptions and limits

S = K / σ assumes uniform smoke between the observer and the target and ordinary lighting. K was measured in nonirritant smoke; above about 0.25 per m, smoke from many materials makes the eyes water and visibility falls faster than the formula predicts. Sign brightness, background lighting and the size of the sign also change K. The fuel-burned option spreads the soot evenly through the volume, which is a screening estimate: in a real fire the smoke collects in a layer, so the layer is denser than the average and the air below it is clearer.

When to bring in an engineer

Visibility is usually the first tenability limit reached in a smoke control analysis, and the answer depends on how fast the layer descends and how much smoke the system removes. DGA designs and reviews smoke control systems and runs fire and smoke modeling to show that escape routes stay tenable.

References

  1. NFPA 92, Standard for Smoke Control Systems, National Fire Protection Association, 2024 edition: Annex M, tenability (visibility guidance in M.3.8).
  2. T. Jin, “Visibility through Fire Smoke,” Journal of Fire and Flammability, Vol. 9, 1978, pp. 135 to 155.
  3. T. Jin and T. Yamada, “Irritating Effects of Fire Smoke on Visibility,” Fire Science and Technology, Vol. 5, No. 1, 1985, pp. 79 to 90.
  4. G.W. Mulholland and C. Croarkin, “Specific Extinction Coefficient of Flame Generated Smoke,” Fire and Materials, Vol. 24, 2000, pp. 227 to 230.
  5. J.D. Seader and I.N. Einhorn, “Some Physical, Chemical, Toxicological, and Physiological Aspects of Fire Smokes,” Sixteenth Symposium (International) on Combustion, The Combustion Institute, 1977, pp. 1423 to 1445.
  6. K. McGrattan et al., Fire Dynamics Simulator User’s Guide, NIST Special Publication 1019, National Institute of Standards and Technology: visibility and mass extinction coefficient defaults.

Frequently Asked Questions

What visibility is used as a tenability criterion?

Many performance-based designs require doors and walls to remain visible at 10 m (33 ft). NFPA 92 Annex M suggests that an illuminated sign be discernible at 30 m (100 ft) and doors and walls at 11.25 m (37 ft). Shorter distances, such as 5 m (16 ft), are sometimes accepted for small rooms that occupants know well. The authority having jurisdiction and the design brief set the value for a project.

How do you convert optical density to extinction coefficient?

Optical density per unit length uses base-10 logarithms, while the extinction coefficient uses natural logarithms. Multiply the optical density per meter by 2.303 to get the extinction coefficient per meter. For example, 0.2 OD per m equals an extinction coefficient of 0.46 per m.

Why can an exit sign be seen farther than a wall in the same smoke?

A light-emitting sign sends its own light toward the observer, so it stays above the threshold of contrast at a longer distance than a surface that only reflects room light through the smoke. Experiments put the constant K at about 8 for light-emitting signs and about 3 for reflecting objects, so a lit sign is seen roughly 2.7 times farther.

What mass specific extinction coefficient should be used?

Measurements of smoke from many flaming fuels give about 8.7 m2/g, which is also the default in widely used fire models. Smoke from smoldering or pyrolysis is lighter in color and scatters more weakly per gram, so a lower value, about 4.4 m2/g, is used for it.

Related Tools and Services

More smoke control and tenability calculators

Engineering aid only, provided as is and without warranty. Results depend on the inputs and on the simplifying assumptions of the method summarized on each tool page, and DGA has not verified them for your application. They do not replace code-required design, testing or review by the licensed engineer responsible for the project. Use of the tools is subject to the Terms of Use.

Related Reading

Articles from DGA Insights on the code and the method behind this calculator.

Quick inquiry

Need these results reviewed for a submittal?

Your name, a way to reach you, and where the project is. One of our licensed PEs replies within one business day. Every inquiry is confidential.

Prefer to describe it first? Open the Project Desk