Free Engineering Tool · NIST and NUREG-1805 data

Heat of Combustion Table

Look up the heat of combustion of 50 common gases, liquids, fuels, plastics and wood, with the public source for every value, then turn a mass loss rate into a heat release rate and a burned mass into total energy.

  • Based on NIST and NUREG-1805 data
  • Free, runs in your browser; your inputs stay on your device
  • Screening tool, not reviewed or sealed by a licensed engineer
  • Last updated October 2026

Screening tool, not engineering advice. This calculator estimates results with simplified published methods. It has not been reviewed or sealed by a licensed engineer for your project, and DGA does not warrant that its results are accurate, complete or suitable for any use. Check every result independently and have the licensed professional responsible for your project review it before you rely on it. Use is subject to the Terms of Use.

Heat of Combustion Table

Net: complete combustion with water as vapor (use for fire calculations). Effective: heat actually released per unit mass lost in fire tests. Gross: water condensed (bomb calorimeter value). Select a name to load it into the calculator. Sources: NIST = NIST Chemistry WebBook, calculated from enthalpies of formation at 25 °C (fuel in the state listed); NUREG-1805 = large pool fire data for liquid fuels; FAA = oxygen bomb calorimeter data for polymers; USDA FPL = Wood Handbook.

Heat Release From Burning Rate

Heat release rate
0
Energy released
0
Burning time at this rate
0
Heat released per unit mass
0

Comparison Chart

Keep these results

About This Tool

The table gives up to three values per material. The net (lower) heat of combustion is the energy released by complete burning with the water in the products left as vapor, which is the condition in a fire. The gross (higher) value also counts the heat given up when that water condenses; it is what an oxygen bomb calorimeter measures. The effective value is the heat actually released per unit mass lost in a fire test, which is lower than the net value when the flame produces soot and carbon monoxide.

For pure gases and liquids, net and gross values are calculated from the standard enthalpies of formation in the NIST Chemistry WebBook by Hess’s law: ΔHc = Σ ΔHf(fuel) − Σ ΔHf(products), with −393.51 kJ/mol for carbon dioxide and −241.826 (vapor) or −285.830 kJ/mol (liquid) for water, divided by the molar mass. Liquids are taken as liquids, so the heat needed to vaporize the fuel is already deducted. Polymer values are oxygen bomb measurements published by the FAA, with net = gross − 21.96 kJ/g times the hydrogen mass fraction. Effective values for liquid fuels and oils come from the large pool fire data tabulated in NUREG-1805, and the wood value is the approximate figure given in the USDA Wood Handbook. Per unit mass of oxygen consumed, most organic fuels release close to 13.1 kJ/g, the constant behind oxygen consumption calorimetry.

The calculator applies the relation used in NFPA 921 and NUREG-1805: heat release rate Q = χ · ṁ · ΔHc, where ṁ is the mass loss rate and χ the combustion efficiency. The energy from a burned mass m is χ · m · ΔHc, and m / ṁ is the time to burn that mass at a constant rate. Use χ = 1 with an effective value; with a net value, χ = 1 gives an upper bound.

Worked example

A polypropylene storage bin burning in a test loses mass at 15 g/s. With the net value of 42.66 kJ/g and an assumed combustion efficiency of 0.85 for illustration, the heat released per gram is 36.3 kJ/g and the heat release rate is 15 × 36.3 = 544 kW. If the bin holds 4 kg of plastic, burning all of it releases 145 MJ, and at the same rate it would take about 4.4 minutes. With χ = 1 the rate would be 640 kW, the complete-combustion bound.

Assumptions and limits

Values are at 25 °C. Fuel blends such as gasoline and diesel vary from batch to batch. Commercial plastics with fillers, flame retardants or moisture release less than the pure polymers listed, and the wood value applies to oven-dry wood. Effective values depend on fire size and ventilation; the liquid fuel values are for large, well-ventilated pool fires. The calculator does not predict the burning rate itself: the mass loss rate has to come from a test, a burning rate correlation or a design fire. Materials not listed, such as PVC and polyurethane foams, need data from a test or a published source for that product.

When to bring in an engineer

Heat of combustion is one input to a design fire, and the result depends heavily on the burning rate chosen. DGA builds design fires and runs fire and smoke modeling for performance-based designs and supports equivalency reports where a heat release rate has to be justified to the authority having jurisdiction.

References

  1. Linstrom, P.J., and Mallard, W.G., eds., NIST Chemistry WebBook, NIST Standard Reference Database Number 69, National Institute of Standards and Technology, accessed October 2026: standard enthalpies of formation of the pure gases and liquids in the table.
  2. Cox, J.D., Wagman, D.D., and Medvedev, V.A., CODATA Key Values for Thermodynamics, Hemisphere Publishing, New York, 1989: enthalpies of formation of carbon dioxide and water.
  3. Iqbal, N., and Salley, M.H., Fire Dynamics Tools (FDTs): Quantitative Fire Hazard Analysis Methods for the U.S. Nuclear Regulatory Commission Fire Protection Inspection Program, NUREG-1805, U.S. Nuclear Regulatory Commission, 2004, Chapter 3; and NUREG-1805 Supplement 1, Vol. 2, 2013, Appendix A: burning rate data for liquid hydrocarbon fuels (effective heat of combustion).
  4. Babrauskas, V., “Estimating Large Pool Fire Burning Rates,” Fire Technology, 19 (4), 1983, pp. 251 to 261.
  5. Lyon, R.E., Hackett, S.M., and Walters, R.N., Heats of Combustion of High-Temperature Polymers, DOT/FAA/AR-TN97/8, Federal Aviation Administration, 1998; and Walters, R.N., Hackett, S.M., and Lyon, R.E., “Heats of Combustion of High Temperature Polymers,” Fire and Materials, 24, 2000, pp. 245 to 252.
  6. White, R.H., and Dietenberger, M.A., “Fire Safety of Wood Construction,” Chapter 18 in Wood Handbook: Wood as an Engineering Material, FPL-GTR-190, USDA Forest Service, Forest Products Laboratory, 2010.
  7. Huggett, C., “Estimation of Rate of Heat Release by Means of Oxygen Consumption Measurements,” Fire and Materials, 4 (2), 1980, pp. 61 to 65.
  8. Babrauskas, V., and Peacock, R.D., “Heat Release Rate: The Single Most Important Variable in Fire Hazard,” Fire Safety Journal, 18, 1992, pp. 255 to 272.
  9. NFPA 921, Guide for Fire and Explosion Investigations, National Fire Protection Association, 2024 edition: heat release rate, mass loss rate and effective heat of combustion.

Frequently Asked Questions

What is the difference between net and gross heat of combustion?

Both assume complete burning. The gross (higher) value counts the heat released when the water formed in combustion condenses to liquid, as it does in a bomb calorimeter. The net (lower) value leaves the water as vapor, which is what happens in a fire, so fire calculations use the net value. For hydrocarbons the gross value is about 7 to 11 percent higher; for carbon monoxide and PTFE, which form no water, the two are equal.

What is the effective heat of combustion?

It is the heat actually released per unit mass of fuel lost in a fire test, measured by oxygen consumption or a similar method. Because flames leave some fuel partly burned as soot and carbon monoxide, the effective value is usually lower than the net value. The ratio of the two is the combustion efficiency.

How do you calculate heat release rate from mass loss rate?

Multiply the mass loss rate by the heat of combustion and by the combustion efficiency. For example, 50 g/s of heptane with an effective value of 44.6 kJ/g gives 50 x 44.6 = 2,230 kW. Use the effective value with an efficiency of 1, or the net value with an efficiency below 1 when a value for the fuel is known.

Why do alcohols and some plastics have lower heats of combustion than hydrocarbons?

Fuels that already contain oxygen, such as methanol, ethanol, acetal (POM) and polyester, are partly oxidized, so less energy is left to release. Methanol gives about 20 kJ/g against 50 kJ/g for methane. Fuels with fluorine or chlorine, such as PTFE, release even less.

Related Tools and Services

More reference data and conversions calculators

Engineering aid only, provided as is and without warranty. Results depend on the inputs and on the simplifying assumptions of the method summarized on each tool page, and DGA has not verified them for your application. They do not replace code-required design, testing or review by the licensed engineer responsible for the project. Use of the tools is subject to the Terms of Use.

Quick inquiry

Need these results reviewed for a submittal?

Your name, a way to reach you, and where the project is. One of our licensed PEs replies within one business day. Every inquiry is confidential.

Prefer to describe it first? Open the Project Desk