Water Supply · Calculation

How Do You Size a Fire Pump (Rated Flow and Pressure)?

Reviewed by a licensed Professional Engineer · NY, NJ, PA, MD, DE · Last reviewed · Code basis: NFPA 20 Ch 4, 6 and 7 (2016 NYC via 2022 BC Appendix Q; 2025 DE; editions referenced by the 2024 I-Codes for NYS and NJ and by the 2021 IBC for PA and MD); NFPA 13 (2022) Ch 4, 19 and 28; NFPA 14 Ch 7

General guidance, not a code determination for any project. Confirm the adopted code and local amendments with the authority having jurisdiction.

A fire pump is sized by subtracting the pressure the water supply can deliver at the system demand flow from the pressure the system needs at the pump discharge, then picking the next listed rated flow at or above the demand and a rated pressure that covers that difference with margin. The selection is then checked at two more points on the pump curve: 150 percent of rated flow, where the pump must still have positive suction, and churn (shutoff), where the pump pressure plus the static suction pressure must stay below the rating of the system components.

The method comes from National Fire Protection Association (NFPA) 20, Standard for the Installation of Stationary Pumps for Fire Protection, Chapter 4 (general requirements, pump selection and suction supply), with the centrifugal pump performance rules in Chapter 6 and the vertical turbine rules in Chapter 7. The demand side comes from the sprinkler calculation under NFPA 13, Standard for the Installation of Sprinkler Systems (2022), Chapter 28, or the standpipe demand under NFPA 14, Standard for the Installation of Standpipe and Hose Systems, Chapter 7. This article walks through the inputs, the steps and a worked example with real numbers. Whether a project needs a pump at all is a separate question, covered in DGA’s article on how engineers decide whether a fire pump is needed.

At a Glance: Sizing a Fire Pump

  • What is calculated: the pump’s rated flow (gpm) and rated pressure (psi), the two numbers on the nameplate that the manufacturer’s curve is built around.
  • Method in one line: the pump adds the difference between the pressure the system needs at the pump discharge and the pressure the supply provides at that flow, with the 150 percent and churn points checked afterward.
  • Inputs needed: system demand (gpm and psi at the pump discharge, hose allowance included), the supply curve from a flow test, elevation to the highest demand point, friction and device losses between the pump and the demand point.
  • Code and section: NFPA 20 Chapter 4 (selection and suction supply) and Chapter 6 (centrifugal pumps); NFPA 13 (2022) Chapter 28 for sprinkler demand; NFPA 14 Chapter 7 for standpipe demand. Editions by state are in the jurisdiction table.
  • Typical result range (units): 500 to 1,500 gpm at 40 to 120 psi for most sprinklered commercial buildings; 750 to 1,500 gpm at 100 psi or more where a standpipe sets the demand. Listed rated flows run from 25 gpm to 5,000 gpm.
  • Most common input error: taking the demand at the base of the riser instead of at the pump discharge, which drops the elevation to the roof and the losses through the pump room piping.

What Inputs Does a Fire Pump Sizing Calculation Need?

Every number in the calculation is either a demand (what the system needs) or a supply (what the water source gives). The table lists each input, its units and where it comes from. The supply inputs depend on a flow test that NFPA 13 (2022) Chapter 4 requires to be no more than 12 months old at the time of working plan submittal unless the authority having jurisdiction (AHJ) approves otherwise.

InputUnitsSource
System demand flowgpmSprinkler hydraulic calculation under NFPA 13 (2022) Chapter 28, or the standpipe demand under NFPA 14 Chapter 7, whichever governs
Hose allowancegpmNFPA 13 (2022) Chapter 19 inside and outside hose, added to the sprinkler flow; for a standpipe the hose demand is the system demand itself
Demand pressure at the pump dischargepsiThe pressure at the remote area or the most remote hose outlet, plus elevation, plus friction from the pump discharge to that point, plus device losses
Elevationft, converted at 0.433 psi per ftHeight from the pump discharge centerline to the highest sprinkler or hose outlet in the calculation
Friction losses, pump to demand pointpsiHazen-Williams calculation through the discharge piping, risers and feed mains, usually already inside the hydraulic calculation
Device lossespsiBackflow preventer, check valves, strainers, flow meter and any pressure-regulating valve, from the manufacturer’s loss curves at the demand flow
Suction supply curvepsi at a range of gpmStatic and residual pressures from the hydrant flow test, projected on N^1.85 graph paper; a tank supply gives a fixed head instead
Suction lossespsiFriction through the service main, the suction piping and the backflow preventer if it sits on the suction side
Safety marginpsiDesign practice, not a code number: commonly 5 to 10 psi at the demand point, or about 10 percent of the demand pressure

The demand flow is the larger of the sprinkler demand with hose and the standpipe demand, not their sum, unless the AHJ or the insurer asks for a combined figure. For a Class I standpipe the demand values commonly applied under NFPA 14 are 500 gpm for the first standpipe and 250 gpm for each additional standpipe, with a total that NFPA 14 caps at 1,000 gpm in a building sprinklered throughout and 1,250 gpm otherwise, at 100 psi residual at the most remote 2.5 in. outlet. The design team confirms those figures against the NFPA 14 edition the AHJ adopts before using them.

What Is the Method for Sizing the Pump?

The method has six steps. The first four set the pump’s rated point; the last two check that the rest of the curve behaves. The arithmetic is simple enough to do by hand once the supply curve and the demand point are fixed.

Figure 1: The Three Numbers Behind a Pump Selection

Pressure the pump must add: Ppump = Pdemand − Psuction, where Pdemand is the pressure the system needs at the pump discharge at the demand flow Qdemand, and Psuction is the pressure the supply delivers at that same flow, read from the supply curve.

Rated point: Qrated is the next listed capacity at or above Qdemand; Prated is Ppump plus the safety margin, rounded up to a pressure the manufacturer offers.

Overload check: at 1.5 × Qrated, the pump delivers at least 0.65 × Prated, and the supply curve must still show positive suction at that flow.

Churn check: Pchurn is not more than 1.4 × Prated; Pchurn + Pstatic suction must not exceed the 175 psi rating of standard components; if it does, the pump is reselected or higher-rated components are specified, because NFPA 20 Chapter 4 does not accept a pressure relief valve as the means of meeting this limit.

Under NFPA 20 Chapter 6, a centrifugal fire pump must deliver at least 150 percent of rated flow at not less than 65 percent of rated pressure, and its churn pressure may not exceed 140 percent of rated pressure. Vertical turbine pumps meet the same 150, 65 and 140 percent limits, stated on total head, under Chapter 7.

Figure 2: Fire Pump Sizing in Six Steps

1. Fix the demand pointTake the governing demand flow with hose allowance and carry its pressure to the pump discharge: remote area pressure plus elevation plus friction plus device losses.
2. Read the suction pressurePlot the flow test on N^1.85 paper, subtract suction-side losses and read the pressure available at the demand flow.
3. Pump adds the differenceDemand pressure minus suction pressure is the net pressure the pump must add at the demand flow.
4. Pick the rated pointChoose the next listed rated flow at or above the demand and a rated pressure that covers the difference with margin.
5. Check 150 percentAt 1.5 times rated flow the pump gives at least 65 percent of rated pressure; confirm the supply still has positive pressure at that flow.
6. Check churnChurn is at most 140 percent of rated pressure; add static suction and compare with the 175 psi component limit; a relief valve does not cure an excess.
The rated point is set in steps 1 to 4; steps 5 and 6 check the ends of the curve. A pump that passes the rated point but fails the 150 percent suction check or the churn limit is resized, or the system is built with components rated for the higher pressure.

Step 1 is where most of the engineering sits. The demand point has to be expressed at the pump discharge flange, not at the base of the riser or at the remote sprinkler, so the elevation to the roof and the losses through the discharge piping, check valve and any backflow preventer are added before the pump is sized. On a combined sprinkler and standpipe system the standpipe outlet pressure usually governs, and the elevation to the roof-level hose valve is the largest single term.

Step 2 depends on the supply curve, and the curve comes from a hydrant flow test read on N^1.85 paper. DGA’s article on how a hydrant flow test is run and read under NFPA 291 covers the test itself; for pump sizing the only outputs needed are the static pressure and the residual pressure at the demand flow and at 150 percent of rated flow. Where the suction comes from a city main, the purveyor may also set a minimum residual that the pump may not pull below, and that limit is checked in the same step.

Step 4 uses the listed rated capacities in NFPA 20 Chapter 4. Rated flows run from 25 gpm to 5,000 gpm, with 500, 750, 1,000 and 1,500 gpm the sizes most often seen on commercial projects. The pump is rated at the next size at or above the demand; sizing to a larger step than necessary pushes the demand point far down the curve and raises the churn pressure for no benefit.

Worked Example: 750 gpm at 95 psi at the Pump Discharge

A 1-story distribution warehouse in central New Jersey has a wet pipe sprinkler system. The hydraulic calculation puts the governing sprinkler demand, with the inside hose allowance, at 750 gpm, with 95 psi required at the pump discharge once the remote area pressure, elevation and discharge piping losses are carried back to the pump. The hydrant flow test on the street main gives 65 psi static and 48 psi residual at 900 gpm, measured at the point of connection with suction-side losses already deducted.

StepCalculationResult
1. Demand pointFrom the hydraulic calculation, at the pump discharge750 gpm at 95 psi
2. Suction at 750 gpm65 psi static, 48 psi at 900 gpm, projected on N^1.85 paper to 750 gpm (52.9 psi by calculation, rounded down for margin)52 psi
3. Pump must add95 psi − 52 psi43 psi
4. Rated pointNext listed flow at or above 750 gpm is 750 gpm; 43 psi plus margin, rounded to an available pressure750 gpm at 50 psi rated
Rated point check52 psi suction + 50 psi pump = 102 psi at the discharge against 95 psi required7 psi margin
5. 150 percent check1.5 × 750 = 1,125 gpm; pump gives at least 0.65 × 50 = 32.5 psi; supply curve at 1,125 gpm reads 39 psiSuction positive (39 psi); discharge about 71 psi
6. Churn checkChurn at most 1.4 × 50 = 70 psi; 70 psi + 65 psi static suction135 psi, below 175 psi; standard components acceptable

The selected pump is a 750 gpm, 50 psi centrifugal fire pump. At the rated point the discharge pressure is 102 psi against a 95 psi demand, a 7 psi cushion that absorbs a modest drop in the city main over the life of the building. At 1,125 gpm the supply still delivers 39 psi, so the pump is never starved during the 150 percent test, and churn plus static suction of 135 psi stays below the 175 psi working pressure of standard fittings.

Figure 3: Supply, Pump and Demand for the Worked Example

0255075100125150 02505007501,0001,250 Flow, gpm Pressure, psi Demand 750 gpm at 95 psi Discharge 102 psi at 750 gpm Churn + static: 135 psi Suction 52 psi at 750 gpm 39 psi at 1,125 gpm 71 psi at 1,125 gpm Pump net: 70 psi churn, 50 psi rated, 32.5 psi at 150% Supply curve (65 psi static, 48 psi at 900 gpm) Pump net pressure Pump plus suction at the discharge
With 65 psi static and 48 psi at 900 gpm on the suction side, a 750 gpm, 50 psi pump delivers 102 psi at the demand flow against 95 psi required, keeps 39 psi of suction at 1,125 gpm, and reaches 135 psi at churn, below the 175 psi component limit.

Plotting the demand point against the supply alone, before any pump, is its own exercise, and DGA’s article on how to plot sprinkler demand against the supply curve covers that step and the cushion it should show. The fire pump sizing calculator runs the same six steps from a flow test and a demand point, and the fire pump test curve plotter draws the resulting curve once the pump is installed and tested.

Opens the Project Desk with your sentence. Our licensed PEs review every brief and reply within one business day.

What Are the Common Errors in Fire Pump Sizing?

Most sizing errors come from a demand point that was never carried to the pump discharge, or from a selection that satisfies the rated point and nothing else. The table lists the errors DGA’s engineers see most often in review, how they show up and the fix.

ErrorHow it shows upFix
Sizing to the demand with no marginThe pump curve passes through the demand point exactly; a 3 psi drop in the city main puts the system below demandAdd 5 to 10 psi at the demand point, or about 10 percent of the demand pressure, before picking the rated pressure
Skipping the 150 percent suction checkThe pump passes at rated flow but the supply curve crosses 0 psi below 1.5 times rated flow; the annual flow test cavitates or cannot reach 150 percentRead the supply curve at 1.5 × Qrated; if suction goes negative, reduce the rated flow, add a break tank or change the source
Forgetting elevation to the roofDemand taken at the base of the riser; the roof hose valve or the top-floor remote area is 20 to 40 psi shortCarry the demand to the pump discharge with 0.433 psi per ft of elevation to the highest outlet
Oversizing the rated flowA 1,500 gpm pump on a 750 gpm demand; the demand point sits far down the curve, churn pressure rises and the pump room needs larger piping and powerRate the pump at the next listed size at or above the demand, not two sizes up
Reading rated pressure off a vendor curve with no factorThe catalog curve shows exactly the demand pressure at the demand flow, but field tolerance and impeller trim leave the installed pump shortSelect from the certified curve with margin, and confirm at the acceptance test that the installed pump meets the rated point
Ignoring churn plus staticChurn 90 psi plus 90 psi static reaches 180 psi; standard 175 psi fittings and sprinklers are overpressured when the pump runs against a closed systemCheck Pchurn + Pstatic; where the sum exceeds 175 psi, reselect the pump for a lower churn pressure or specify higher-rated components; NFPA 20 Chapter 4 does not accept a relief valve as the fix

The 150 percent check is the one that catches engineers who size from a tank in their head but connect to a city main in the drawings. A main that delivers 52 psi at 750 gpm can be at 10 psi or lower at 1,125 gpm on a weak system, and the acceptance test, described in DGA’s article on what happens at a diesel fire pump acceptance test, will show it. Whether the driver is electric or diesel does not change the sizing method, only the controller, power supply and room requirements.

Where Does the Method Stop and a Professional Engineer’s Calculation Begin?

The six-step method sizes a single centrifugal pump drawing from a public main or a tank with a known curve. Several situations fall outside it and need a licensed Professional Engineer (PE) to run the full hydraulic analysis and sign the selection.

SituationWhy the simple method is not enough
Vertical turbine pumpsThe pump draws from a wet pit or well; NFPA 20 Chapter 7 applies the same 150, 65 and 140 percent limits to total head, and the pumping water level and bowl submergence replace the suction pressure in the calculation
Pumps in series or parallelHigh-rise zones and large campuses stack pumps; the combined curve, the sequencing and the suction to the second pump are modeled, not read from a single chart
Weak or variable city supplyWhere the supply curve crosses 0 psi near 150 percent of rated flow, or where the purveyor imposes a residual floor, a break tank or a different rated flow may be required
Churn plus static above 175 psiHigh static suction or a high rated pressure needs a reselected pump, components rated for the actual pressure and pressure-regulating valves at the outlets downstream of the pump, each a design decision
Variable speed pressure limitingA variable speed controller changes the shape of the delivered curve; the selection has to be checked at the limited pressure and at full speed
Insurer design basisFM Global and other carriers may require a larger demand, a different hose allowance or a specific margin that moves the rated point above the code minimum

In every one of those cases the sizing still starts with the same three numbers: the demand at the pump discharge, the suction at that flow and the difference between them. What changes is how the supply curve is built and how many times the check is repeated.

Which NFPA 20 Edition Applies in Each State?

The sizing method is the same in every edition of NFPA 20 that DGA’s jurisdictions adopt, but the edition in force sets the acceptance test, the controller and the pump room rules that follow. The edition comes from the referenced standards chapter of the building code the AHJ adopts, not from NFPA’s newest publication.

JurisdictionNFPA 20 editionAHJFiling or permit
New York State (outside NYC)2025 Uniform Code (2024 I-Codes); the NFPA 20 edition referenced by the 2024 I-CodesLocal code enforcement officialBuilding permit, with the fire pump on the sprinkler or standpipe submittal
New York City2022 Building Code; Appendix Q modifies NFPA 20 (2016)Department of Buildings (DOB) for plan review; a DOB inspector or a professional chosen by the permit holder witnesses the fire pump acceptance flow testDOB NOW: Build sprinkler or standpipe filing with the fire pump shown; fire pump test result tracked in DOB NOW
New JerseyUniform Construction Code (UCC), 2024 I-Codes effective August 17, 2026; the NFPA 20 edition referenced by the 2024 I-CodesMunicipal fire protection subcode officialUCC construction permit, fire protection subcode technical section
PennsylvaniaUCC, 2021 I-Codes effective January 1, 2026; the NFPA 20 edition referenced by the 2021 International Building Code (IBC)Municipal or third-party code official; Department of Licenses and Inspections (L&I) in PhiladelphiaBuilding permit with the fire protection submittal; no statewide fire code
Maryland2021 IBC through the county building permit; the NFPA 20 edition referenced by the 2021 IBC; State Fire Prevention Code is NFPA 1 (2024)County building official; State or local fire marshal under the AHJ’s permit policyCounty building permit; fire marshal plan review where the county’s policy requires it
DelawareState Fire Prevention Regulations (Regulation 701, 2026): NFPA 20 (2025); IBC by countyOffice of the State Fire Marshal (Wilmington Fire Marshal inside the city); county building officialState Fire Marshal plan review before the county building permit

Editions as of November 2026. Local amendments are not shown.

Key Takeaway: A fire pump adds the pressure the supply lacks at the demand flow. Size it by carrying the demand to the pump discharge, reading the suction at that flow, rating the pump at the next listed capacity with a pressure that covers the difference and a margin, then checking that the supply is still positive at 150 percent of rated flow and that churn plus static suction stays below 175 psi. The worked example lands on 750 gpm at 50 psi with a 7 psi cushion.

Frequently Asked Questions

Should the fire pump be rated at the system demand flow?

Yes, at the next listed rated flow at or above the demand. NFPA 20 Chapter 4 lists the rated capacities, and a pump sized two steps above the demand pushes the operating point far down the curve, raises churn pressure and enlarges the pump room for no gain.

Does the rated pressure equal the demand pressure?

No. The rated pressure is the difference between the demand pressure at the pump discharge and the suction pressure at that flow, plus a safety margin of about 5 to 10 psi. In the worked example the pump must add 43 psi and is rated at 50 psi.

What happens if the supply goes to 0 psi before 150 percent of rated flow?

Conditional: the selection fails as drawn, because the pump cannot be tested to 150 percent of rated flow with positive suction. The options are a smaller rated flow, a break tank between the main and the pump, or a different water source, and the choice is a PE design decision.

When does a fire pump need a pressure relief valve?

Conditional: NFPA 20 Chapter 4 calls for one mainly where a diesel engine drive or a variable speed pressure limiting control can push the discharge above the rating of the system components, usually 175 psi. A relief valve is not an accepted way to keep churn plus static suction under that rating; the pump selection or higher-rated components do that.

This article is general information, not a fire pump selection for any project. Code editions, local amendments and purveyor rules change; confirm the adopted edition of NFPA 20 and the authority having jurisdiction before a pump is specified.

Need a Fire Pump Sized for a Permit Set?

Send the hydraulic calculation, the hydrant flow test and the building height. DGA sizes the pump, checks the 150 percent and churn points and prepares the sealed selection for the AHJ. Project briefs get confirmation and preliminary code feedback within one business day.

Send a Project Brief → View Fire Pump Design

Leave a Reply

Your email address will not be published. Required fields are marked *

Quick inquiry

Ready when you are.

Your name, a way to reach you, and where the project is. One of our licensed PEs replies within one business day. Every inquiry is confidential.

Prefer to describe it first? Open the Project Desk