Free Engineering Tool · NUREG-1805

Time to Ignition Calculator

Enter the radiant heat flux reaching a surface and the material’s ignition properties. The calculator estimates how long the surface takes to reach its ignition temperature, checks the flux against the critical heat flux below which it will not ignite, and plots ignition time against flux, following the NUREG-1805 Fire Dynamics Tools method.

  • Based on NUREG-1805
  • Free, runs in your browser; your inputs stay on your device
  • Screening tool, not reviewed or sealed by a licensed engineer
  • Last updated October 2026

Screening tool, not engineering advice. This calculator estimates results with simplified published methods. It has not been reviewed or sealed by a licensed engineer for your project, and DGA does not warrant that its results are accurate, complete or suitable for any use. Check every result independently and have the licensed professional responsible for your project review it before you rely on it. Use is subject to the Terms of Use.

Advanced method. The correlations behind this tool come from research and test data with narrow ranges of validity. Outside those ranges results can be wrong by a wide margin, and they are no substitute for a fire model or an analysis by a qualified fire protection engineer.

Exposure

Material

Result

Time to ignition
0
Upper estimate with surface losses
0
Critical heat flux (estimate)
0
Heat flux to ignite in 60 s
0

Time to Ignition and Heat Flux

Keep these results

About This Tool

A combustible surface exposed to radiant heat ignites, when a pilot flame or spark is present, once its surface reaches an ignition temperature Tig. How fast that happens depends on how quickly the heat soaks into the material. For a thermally thick solid, where the heat has not reached the back face by the time of ignition, the solution for a semi-infinite solid with no surface losses gives tig = (π/4) kρc [(Tig − T0)/q″]2. The product kρc, the thermal inertia, is why low-density foams ignite in seconds while dense wood takes much longer. For a thermally thin sheet about a millimeter thick or less, the whole thickness heats together and tig = ρcδ (Tig − T0)/q″.

Both formulas ignore heat lost from the surface by re-radiation and convection, so they give the shortest likely time. Losses set a critical heat flux q″cr = hT (Tig − T0) below which the surface never reaches Tig, where hT is a combined heat transfer coefficient; about 45 W/m²·K is a common linearized value. The calculator also solves the same heating problem with that loss included, which gives an upper estimate: for a thick solid the surface temperature rise is (q″/hT) [1 − eβ² erfc β] with β = hT√(t/kρc), and for a thin sheet t = (ρcδ/hT) ln[q″/(q″ − q″cr)]. Far above the critical flux the two estimates converge; near it the loss solution grows without bound.

The material presets list ignition temperatures and effective thermal inertias measured with the lateral ignition and flame spread test (ASTM E1321) for common building and interior materials. They are effective values: they fold in-depth absorption, charring and test conditions into kρc, so they are best used with the thick formula as here.

Worked example

Plywood (Tig = 390 °C, kρc = 0.54) starting at 20 °C is exposed to 35 kW/m². The thick formula gives (π/4) × 0.54 × (370/35)2 = 47 s. The critical heat flux is 0.045 × 370 = 16.7 kW/m², so ignition is expected; with surface losses the estimate stretches to about 2.2 minutes. To ignite within 60 s the plywood needs about 31 kW/m². A 1 mm sheet with a density of 700 kg/m³, a specific heat of 1.3 kJ/kg·K and the same ignition temperature would ignite in about 10 s at the same flux.

Assumptions and limits

The material is inert until ignition, the flux is constant and uniform, and a pilot is present; without a pilot, surfaces must get much hotter before they ignite. Properties change with moisture, aging, surface coatings and orientation, and test-derived values carry the conditions of the test. Above about 100 kW/m² the inert-solid assumption breaks down. Thin materials on a backing behave between the thin and thick cases depending on the backing.

When to bring in an engineer

Ignition of secondary items is often what turns a small fire into a large one, and it decides separation distances, target spacing in performance-based designs and the timeline in fire investigations. DGA evaluates ignition and fire spread as part of fire modeling and provides expert witness support where ignition timing is in question.

References

  1. Iqbal, N., and Salley, M.H., Fire Dynamics Tools (FDTs): Quantitative Fire Hazard Analysis Methods for the U.S. Nuclear Regulatory Commission Fire Protection Inspection Program, NUREG-1805, U.S. Nuclear Regulatory Commission, 2004, Chapter 6.
  2. Mikkola, E., and Wichman, I.S., “On the Thermal Ignition of Combustible Materials,” Fire and Materials, 14 (3), 1989, pp. 87 to 96.
  3. Quintiere, J.G., and Harkleroad, M., New Concepts for Measuring Flame Spread Properties, NBSIR 84-2943, National Bureau of Standards, 1984.
  4. ASTM E1321, Standard Test Method for Determining Material Ignition and Flame Spread Properties, ASTM International, current edition.
  5. NFPA 921, Guide for Fire and Explosion Investigations, National Fire Protection Association, 2024 edition: ignition of solid fuels and thermal inertia.

Frequently Asked Questions

What is the difference between thermally thick and thermally thin?

A thermally thin material is heated through its whole thickness, so its temperature is nearly uniform; paper, fabrics and sheets about a millimeter thick or less behave this way. A thermally thick material is still near its starting temperature at the back when the front ignites, which is the case for most boards, plastics and furniture components.

What is the critical heat flux for ignition?

It is the lowest incident heat flux that can bring a surface to its ignition temperature, because below it the surface loses heat by radiation and convection as fast as it gains it. For common wood products and plastics it is typically in the range of about 10 to 20 kW/m2.

Why do foams ignite so much faster than wood?

Ignition time of a thick solid is proportional to its thermal inertia, the product of thermal conductivity, density and specific heat. Low-density foams can have a thermal inertia ten or more times lower than wood, so their surface heats almost immediately.

Which value should be used for design, the time with or without losses?

The time without surface losses is the shorter, conservative value and is the usual choice when a target must not ignite before some event, such as sprinkler operation. The time with losses shows how much longer ignition could take when the flux is only modestly above the critical value.

Related Tools and Services

More fire dynamics and detection calculators

Engineering aid only, provided as is and without warranty. Results depend on the inputs and on the simplifying assumptions of the method summarized on each tool page, and DGA has not verified them for your application. They do not replace code-required design, testing or review by the licensed engineer responsible for the project. Use of the tools is subject to the Terms of Use.

Related Reading

Articles from DGA Insights on the code and the method behind this calculator.

Quick inquiry

Need these results reviewed for a submittal?

Your name, a way to reach you, and where the project is. One of our licensed PEs replies within one business day. Every inquiry is confidential.

Prefer to describe it first? Open the Project Desk