Licensed PEs in NY · NJ · PA · MD · DE · WA · OR · FLMon to Fri, 9am to 5pm ET · (646) 355-8274 · info@dgaconsulting.net · Project Desk

Sprinkler Systems · Calculation

How do you size a water supply for a 13R or 13D system?

General guidance, not a code determination for any project. Confirm the adopted code and local amendments with the authority having jurisdiction.

A water supply for a National Fire Protection Association (NFPA) 13R or 13D sprinkler system is sized by multiplying the design flow by the duration the standard sets: up to 4 sprinklers in the most demanding compartment for 30 minutes under NFPA 13R, and up to 2 sprinklers for 10 minutes under NFPA 13D, or 7 minutes in a one-story home under 2,000 sq ft. The source then has to deliver that flow at the pressure the hydraulic calculation needs for the whole time, and a tank has to hold the result in water it can actually deliver. Two sprinklers at 13 gpm in a two-story home come to 26 gpm and 260 gallons, and four sprinklers that calculate at 68 gpm in an apartment building come to 2,040 gallons.

This article covers the inputs, the method, worked examples for a home on a well and an apartment building with a break tank, and how pumps and tanks change the numbers. What NFPA 13D requires of a home as a whole, and which homes must have a system, is covered in DGA’s guide to what NFPA 13D requires for a one- or two-family home.

At a Glance: Sizing a 13R or 13D Water Supply

  • What is calculated: the flow, pressure and volume a water supply must deliver to an NFPA 13R or 13D sprinkler system, and the water a tank must store where the source cannot carry the demand alone.
  • Method in one line: volume = design flow × duration, with the source checked for that flow at the pressure the hydraulic calculation needs, and only the water a tank can deliver at pressure counted toward the volume.
  • Inputs needed: the most demanding compartment and the listed flow and pressure of its design sprinklers; friction, meter and device losses; the height of the highest design sprinkler; the source data (flow test, pump curve and pressure settings, well yield, tank dimensions); the duration; any margin the authority having jurisdiction (AHJ) requires.
  • Code and section: NFPA 13R and NFPA 13D in the edition the adopted code references (13R duration in Section 9.2.1; 13D water supplies in Chapter 6, with the stored-water durations in Sections 6.1.2 and 6.1.3); International Residential Code (IRC) Sections P2904.4.2, P2904.5.1 and P2904.5.2 (2018 and 2021 editions) for homes on the residential code’s own sprinkler path; International Fire Code (IFC) Section 507.2.2 and NFPA 22 for water tanks; International Building Code (IBC) Section 913 and NFPA 20 for fire pumps.
  • Typical result range (units): with sprinklers listed at 13 to 25 gpm each, 26 to 50 gpm and about 180 to 500 gallons for a 13D home, and 52 to 100 gpm and about 1,560 to 3,000 gallons for a 13R building, before the extra flow a full hydraulic calculation adds and before unusable tank volume.
  • Most common input error: counting a whole tank as usable water. A pressure tank delivers only its water fraction, not its full volume, and a storage or break tank only the water above the outlet the pump draws from.

How much water does a 13R or 13D system need, and for how long?

Both residential standards size the supply for a few sprinklers in one room rather than for a design area spread across a floor. NFPA 13D designs for up to 2 sprinklers in the compartment with the greatest demand and NFPA 13R for up to 4, each flowing at no less than the greater of the flow its listing requires for the coverage area used and 0.05 gpm per sq ft over that area (NFPA 13D (2022) Sections 10.1.1 and 10.2.1; NFPA 13R (2022) Sections 7.1.1.1 and 7.1.1.3.1). The compartment that governs is usually the one highest above and farthest from the supply, because elevation and friction both add to the pressure it needs.

The durations reflect the standards’ goal of giving occupants time to escape rather than protecting the building. Where stored water is the sole source, NFPA 13D requires 10 minutes of it, or 7 minutes in a dwelling one story high and under 2,000 sq ft (Sections 6.1.2 and 6.1.3), and IRC Section P2904.5.2 sets the same two durations for homes designed to the residential code’s own sprinkler section. NFPA 13R requires 30 minutes (Section 9.2.1) and, unlike NFPA 13, adds no hose stream allowance of its own.

StandardDesign sprinklersDurationWhere it is set
NFPA 13DUp to 2 in the compartment with the greatest demand, each at no less than its listed flow or 0.05 gpm per sq ft, whichever is greater10 minutes; 7 minutes in a dwelling one story high and under 2,000 sq ft; both where stored water is the sole sourceNFPA 13D (2025) Chapter 6 (water supply, Sections 6.1.2 and 6.1.3) and Chapter 10 (hydraulic design); other jurisdictions apply the edition their code references
IRC Section P2904 (homes on the residential code path)The listed flow of a room’s only sprinkler, or 2 times the highest listed flow in a room with 2 or more (Section P2904.4.2)7 minutes for one story under 2,000 sq ft; 10 minutes for 2 or more stories or 2,000 sq ft or more (Section P2904.5.2)2018 and 2021 IRC
NFPA 13RUp to 4 in the compartment with the greatest demand, each at no less than its listed flow or 0.05 gpm per sq ft, whichever is greater30 minutes, with no hose stream allowance in the standardNFPA 13R, in the edition the adopted building code references
NFPA 13, for comparisonA design area set by hazard class30 minutes for light hazard up to 120 minutes for extra hazard, plus a hose stream allowanceNFPA 13 (2022) Chapter 19, Table 19.2.3.1.2

Paraphrased by DGA, not NFPA or International Code Council text.

The arithmetic is the same across the region, but the edition of each standard follows the adopted code. As of November 2026, New York City applies NFPA 13R and 13D in their 2016 editions as modified by Appendix Q of the 2022 New York City Building Code, New York State and New Jersey apply the editions their 2024-based codes reference, and Pennsylvania and Maryland county permits apply the 2019 editions the 2021 IBC references, with homes under the residential code on the NFPA 13D edition it references. Maryland’s State Fire Prevention Code (NFPA 1, 2024) references the 2022 editions, and Delaware’s State Fire Marshal applies the 2025 editions (Regulation 701 sections 3.1.8 and 3.1.10).

What inputs set a 13R or 13D supply’s demand and duration?

Every input comes from the sprinkler listings, the hydraulic calculation or the water source. The table gives each one’s source and the value used in the worked examples.

InputSourceExample
Design sprinklersThe compartment with the greatest demand: up to 2 sprinklers under NFPA 13D, up to 4 under NFPA 13RA living room with 2 sprinklers (13D); a top-floor living room with 4 (13R)
Listed flow and pressureThe sprinkler’s listing for the coverage area and ceiling used; pressure P = (Q ÷ K)213 gpm at 7.0 psi for a K-4.9 sprinkler covering 16 ft by 16 ft
Friction and device lossesHazen-Williams friction in pipe and fittings; the manufacturer’s loss data for the meter, backflow preventer, check valve and flow switch at the design flow9.5 psi of friction and 2.0 psi through devices at 26 gpm
Elevation0.433 psi per foot, from where the supply pressure is measured up to the highest sprinkler (IRC Section P2904.6.2.2, Step 5)20 ft, or 8.7 psi
Available supplyFrom a public main, the residual pressure at the design flow from a current flow test, or on the IRC prescriptive path the purveyor’s static pressure less the service and meter losses (Section P2904.6.2.2); in New York City, the Department of Environmental Protection (DEP) statement of minimum main pressure that documents for a street-pressure system carry (Building Code Section 903.1.2); from a well or tank system, the pump’s minimum pressure control setting (IRC Section P2904.5.1)40 psi, the cut-in of a 40/60 psi pressure switch
DurationNFPA 13D: 10 minutes, or 7 in a one-story home under 2,000 sq ft, where stored water is the sole source; NFPA 13R: 30 minutes10 minutes (13D); 30 minutes (13R)
Well capacity and shared servicesIRC Section P2904.5.2 lets well capacity and tank storage combine to meet the duration; where one water service feeds more than one dwelling, the IRC pipe sizing tables add 5 gpm to the design flowA 5 gpm well, worth 50 gallons over 10 minutes
Safety marginThe AHJ or the insurer; Delaware’s State Fire Marshal requires 10 psi above system demand (Regulation 702 Chapter 4 section 1.3.1.5), and its Preliminary Sprinkler Form asks for the demand plotted with hose streams and that margin12.8 psi available in the 13D example

Local reviewers add their own checks on the supply side. Montgomery County’s Department of Permitting Services (DPS) asks for the Washington Suburban Sanitary Commission (WSSC) low and high hydraulic gradients on an NFPA 13D submittal, applies a 10 percent safety factor to NFPA 13D calculations unless a pump would then be needed, and accepts a pump or tank on public water only after other design options are ruled out. New York City’s Appendix Q lets a 13D system share a supply main with domestic use only where domestic flow stops when the sprinklers operate (section Q103).

How is the required volume calculated, step by step?

The method runs from the most demanding sprinkler back to the source, then multiplies by time. Each step draws on the inputs table, and the formula card collects the relationships in one place.

Figure 1: Water supply formulas for 13R and 13D systems

Design flow: Q = the sum of the design sprinklers’ flows at the supply: up to 2 sprinklers under NFPA 13D, or 2 × the highest listed flow in the room under IRC Section P2904.4.2; up to 4 under NFPA 13R; where one service feeds more than one dwelling, the IRC adds 5 gpm to this flow for the service, meter and device losses only.

Required pressure: Preq = Psprinkler + 0.433 × h + Pfriction + Pdevices, where Psprinkler = (q ÷ K)2 for the most demanding sprinkler and h is its height in feet above the point where the supply pressure is measured.

Volume: V = Q × t, with t = 10 minutes for NFPA 13D (7 in a one-story home under 2,000 sq ft) and 30 minutes for NFPA 13R.

Stored water: Vstored = V − Qwell × t where the code lets a well’s flow count (IRC Section P2904.5.2), plus the water the tank holds but cannot deliver.

Pressure tank: Pair = (Preq + 15) ÷ A − 15 and Vtank = Vstored ÷ (1 − A), where A is the fraction of the full tank that is air and 15 psi stands for atmospheric pressure.

Applied to the worked examples, two 13 gpm sprinklers for 10 minutes need 260 gallons, of which a 5 gpm well supplies 50, so the tank stores 210; four sprinklers that calculate at 68 gpm for 30 minutes need 2,040 gallons of effective capacity in a break tank.
  1. Find the compartment with the greatest demand: up to 2 design sprinklers under NFPA 13D, up to 4 under NFPA 13R.
  2. Add the sprinklers’ flows into the design flow at the supply, by hydraulic calculation or, on the IRC path, as 2 times the highest listed flow.
  3. Add friction, device losses and elevation to the sprinkler pressure to get the pressure the supply must hold.
  4. Check the source at the design flow; the difference between the available and required pressure is the margin.
  5. Multiply the design flow by the duration, subtract any well flow the code lets count, and add the water a tank cannot deliver.
  6. For a pressure tank, set the air fraction and air pressure so the tank still holds the required pressure as it empties.

A public main that passes step 4 needs no tank, while a well or a weak main that fails it needs storage, a pump or both. Whether a project needs a tank in the first place is the subject of DGA’s article on when a fire protection water tank is required.

Opens the Project Desk with your sentence. Our licensed PEs review every brief and reply within one business day.

Worked example: How big a tank does a 13D home on a well need, and a 13R building with a break tank?

The 13D home. A new two-story, 2,600 sq ft home in rural Maryland, where the residential code requires sprinklers in new one- and two-family dwellings, draws its water from a well that tests at a sustained 5 gpm. The most demanding room is a living room with 2 residential pendent sprinklers, each listed at 13 gpm and 7.0 psi (K-4.9) for a 16 ft by 16 ft coverage area. A booster pump with a 40/60 psi pressure switch draws from a storage tank that the well pump keeps full.

StepArithmeticResult
1. Design flow2 × 13 gpm (IRC Section P2904.4.2; 2 design sprinklers under NFPA 13D)26 gpm
2. Pressure needed at the pump7.0 psi sprinkler + 8.7 psi elevation (20 ft × 0.433) + 9.5 psi friction + 2.0 psi devices27.2 psi
3. Pressure creditedThe pump’s minimum pressure control setting (IRC Section P2904.5.1)40 psi, a 12.8 psi margin
4. Volume26 gpm × 10 min, because the home has two stories260 gal
5. Well credit5 gpm × 10 min (IRC Section P2904.5.2)50 gal
6. Stored water260 gal − 50 gal210 gal above the pump outlet
7. TankA 250 gal tank that leaves 20 gal below its outlet230 gal usable, covering the 210 gal

Figure 2: Booster pump curve against the 13D demand

020406080 010203040 Pressure at the pump, psi Flow, gpm Cut-out 60 psi: not credited Cut-in 40 psi: the pressure IRC P2904.5.1 credits Pump curve: 70 psi at no flow 52 psi at 26 gpm Demand: 26 gpm at 27.2 psi Margin 12.8 psi Demand at the pump: 7.0 psi sprinkler + 8.7 psi elevation + 9.5 psi friction + 2.0 psi devices = 27.2 psi.
Under IRC Section P2904.5.1 a well or tank system is credited with the pump’s minimum pressure control setting, so this home’s 40/60 psi switch counts as 40 psi even though the pump makes 52 psi at the 26 gpm design flow. Against the 27.2 psi the two design sprinklers need at the pump, that leaves a 12.8 psi margin.

The pump has to clear two tests, and the figure shows both. Its curve must still deliver 26 gpm at or above the 40 psi cut-in, which this pump does at 52 psi, and the 40 psi it is credited with must exceed the 27.2 psi the sprinklers need, which leaves 12.8 psi. Without the 50 gallon well credit the tank would store all 260 gallons, and the credit holds only where the well pump runs during a fire at its tested rate.

DGA’s guide to when a well or private source can supply fire protection covers the stricter tests a well must pass to feed a fire pump under NFPA 20 directly. A home’s pumps are part of the dwelling’s water system instead, credited at the minimum pressure control setting as the figure shows.

The 13R building. A 4-story, 48-unit apartment building in New Jersey qualifies for NFPA 13R under IBC Section 903.3.1.2, and the water purveyor will not let a fire pump draw from its main. The design therefore fills an atmospheric break tank from the main through an air gap, and a fire pump draws from the tank. The most demanding compartment is a top-floor living room with 4 residential pendent sprinklers, each listed at 16 gpm and 10.7 psi (K-4.9).

StepArithmeticResult
1. Minimum design flow4 × 16 gpm64 gpm
2. Calculated flow at the pumpEach sprinkler at the pressure it actually receives, from the hydraulic calculation68 gpm
3. Pressure needed at the pump discharge10.7 psi sprinkler + 16.5 psi elevation (38 ft × 0.433) + 24.8 psi friction + 6.0 psi devices58.0 psi
4. Effective capacity68 gpm × 30 min, with no hose stream allowance under NFPA 13R2,040 gal
5. Tank8 ft diameter by 7 ft tall: 376 gal per foot, 2,632 gal gross6.0 ft between vortex plate and overflow: 2,256 gal effective

The break tank counts only the 6.0 ft of water between the anti-vortex plate, 0.5 ft above the floor, and the overflow, 0.5 ft below the top, which is how DGA’s guide to sizing a fire protection water storage tank measures effective capacity. Those 2,256 gallons cover the 2,040 required with 216 to spare. The fire pump is then chosen so its curve delivers at least 68 gpm at 58.0 psi plus any margin the AHJ or insurer requires, and the same building in Delaware would need 68.0 psi with the State Fire Marshal’s 10 psi.

The tank above holds the full 30 minutes with no credit for the main that refills it. A smaller break tank that counts on refill during the fire falls under the break tank rules that NFPA 20 (2022) Section 4.33 sends to NFPA 22 (2023) Section 14.5, which set a minimum tank size and automatic refill arrangements, and the AHJ and the purveyor must accept the refill as reliable.

How do pumps, pressure tanks and break tanks fit the calculation?

A pump changes the pressure side of the calculation, not the volume. A home’s pump is credited at its cut-in pressure, as the 13D example shows, and its curve must hold the design flow there. On a 13R building under the IBC, a fire pump serving the sprinklers is installed under IBC Section 913, which references NFPA 20, and is selected from the calculated flow and pressure at its discharge.

A pressure tank stores water under compressed air, so only part of the tank is water. As water leaves, the air expands and its pressure falls, which means the air must start high enough to hold the required pressure as the last water leaves: in absolute terms, the starting air pressure times the air fraction equals the final pressure. DGA’s fire sprinkler pressure tank calculator solves that relationship, which follows NFPA 22 (2023) annex Equation A.7.1.4.2a, for either the air pressure or the air fraction.

The 13D home could hold its water in a pressure tank instead of a storage tank and booster pump. Counting no well flow, the tank holds all 260 gallons and must still deliver 27.2 psi when empty, and the air fraction trades air pressure against tank size.

Air fraction when fullAir pressure to maintainTank volume for 260 gal of water
One-half(27.2 + 15) ÷ 0.5 − 15 = 69.4 psi260 ÷ 0.5 = 520 gal
One-third(27.2 + 15) ÷ (1/3) − 15 = 111.6 psi260 ÷ (2/3) = 390 gal

The higher air pressure buys a smaller tank, and it must stay within the pressure rating of the tank and every component on it.

A break tank is an atmospheric tank filled from the public main through an air gap, so the main never connects to the sprinkler piping and the fire pump never draws on the main. Because its water sits at atmospheric pressure, a pump always follows a break tank. Under the IFC, water tanks for private fire protection are installed to NFPA 22 (Section 507.2.2 in the 2024 edition), and Delaware adopts NFPA 22 (2023) at Regulation 701 section 3.1.18.

An elevated tank makes its own pressure at 0.433 psi for each foot of water above the point of use. Delivering the 13R example’s 58.0 psi at grade without a pump would take about 134 ft of height, far above a 4-story roof.

Which errors are common, and when is a professional engineer’s calculation required?

Each error below takes an input from the wrong place. The table gives its effect, using the worked examples where they apply, and the fix.

ErrorWhat goes wrongFix
Cut-out pressure taken as availableA 40/60 psi well system is credited with 60 psi, 20 psi more than the code allowsUse the pump’s minimum pressure control setting (IRC Section P2904.5.1)
Whole tank countedA 520 gal pressure tank half full of air is counted as 520 gal of water instead of 260Count only the water a tank can deliver at the required pressure, above the outlet the pump draws from
Listed minimums used instead of the calculationA 13R tank sized from 4 × 16 gpm = 64 gpm comes out 120 gal short of the 2,040 gal the calculated 68 gpm needsSize from the calculated flow at the supply
Wrong duration7 minutes applied to a two-story home, or to one of 2,000 sq ft or more, cuts 260 gal to 182 galUse 10 minutes unless the dwelling is both one story high and under 2,000 sq ft
Shared service missedTownhouses on one water service are sized for one dwelling’s flowAdd 5 gpm where the service feeds more than one dwelling (notes to IRC Tables P2904.6.2(1) and P2904.6.2(2), 2021)
Meter and backflow losses left outDevices take pressure out of the margin; Maryland deletes the IRC sentence that excuses a backflow preventer on a dwelling system (Code of Maryland Regulations (COMAR) 09.12.51.04C(6))Take each device’s loss at the design flow from the manufacturer’s data
Refill counted without approvalA break tank is sized for the gap between demand and fill rateSize for the full duration unless the NFPA 22 break tank rules and the AHJ support a smaller tank

The flow-times-duration method holds when one compartment governs, the source holds steady for the whole duration and every gallon counted reaches the sprinklers at pressure. A home on the residential code path may size its pipe by the IRC’s prescriptive method or by a hydraulic calculation to NFPA 13D (IRC Section P2904.6.1), but a pump curve, a pressure tank or a shared service is best carried through a full hydraulic calculation by the engineer responsible for the system.

A 13R building needs an engineered supply design whenever it includes spaces designed to NFPA 13, such as a podium garage or a commercial ground floor, because those spaces bring NFPA 13’s hose allowance and longer duration, which usually govern the tank and the pump. Break tanks and fire pumps add NFPA 22 and NFPA 20 design rules, and where a jurisdiction requires sealed sprinkler drawings the water supply analysis belongs in the sealed set.

Key Takeaway: A 13R or 13D water supply is design flow times duration: up to 4 sprinklers for 30 minutes under NFPA 13R, and up to 2 for 10 minutes, or 7 in a one-story home under 2,000 sq ft, under NFPA 13D, delivered at the pressure the hydraulic calculation needs. The worked examples come to 260 gallons for a two-story home, 210 of them stored beside a 5 gpm well, and 2,040 gallons of effective capacity in a 13R break tank. Count only the water a tank can deliver at pressure, and credit a pump only at the pressure its controls hold.

Frequently asked questions

How long must a 13R water supply last?

30 minutes. NFPA 13R sizes the supply for up to 4 sprinklers in the most demanding compartment for 30 minutes and adds no hose stream allowance of its own, so a 68 gpm demand needs 2,040 gallons. The AHJ can add a margin, as Delaware’s State Fire Marshal does with 10 psi.

How long must a 13D water supply last?

10 minutes in most homes, and 7 minutes in a dwelling one story high and under 2,000 sq ft. NFPA 13D sets those durations for up to 2 flowing sprinklers where stored water is the sole source, and IRC Section P2904.5.2 sets the same two for homes designed to the residential code’s own sprinkler section. Two sprinklers at 13 gpm for 10 minutes need 260 gallons.

Can a 13D system run from a pressure tank?

Yes. NFPA 13D accepts a pressure tank as a water supply, provided its air charge can push out the whole stored volume and still hold the required pressure as the last water leaves. For 260 gallons that must end at 27.2 psi, a tank half full of air needs 69.4 psi in a 520 gallon vessel, and a tank one-third air needs 111.6 psi in a 390 gallon vessel.

Does a 13R tank need a fire pump?

Conditional: a tank at grade, including any break tank, needs a pump to make pressure, while an elevated tank high enough above the sprinklers or a pressure tank with enough air does not. Where a building under the International Building Code uses a fire pump, Section 913 sends its installation to NFPA 20, and the pump must deliver the calculated flow at the required pressure, 68 gpm at 58.0 psi in this article’s example.

This article is general information, not a substitute for a project-specific water supply analysis. Code editions, local amendments and reviewer practice change; confirm the adopted code and the authority having jurisdiction for each project.

Sizing the Water Supply for a 13R or 13D Project?

Send the floor plans, the water source details (a flow test, the purveyor’s pressure letter or the well’s yield test) and the jurisdiction. DGA calculates the demand, sizes any tank, pressure tank or pump, and prepares the sprinkler design and hydraulic calculations for review. Project briefs get confirmation and preliminary code feedback within one business day.

Send a project brief → View related services

Leave a reply

Your email address will not be published. Required fields are marked *

Quick inquiry

Ready when you are.

Your name, a way to reach you, and where the project is. A licensed PE replies within one business day. Every inquiry is confidential.

Prefer to describe it first? Open the Project Desk

FirmDGA Fire Protection Engineering
SheetFP-5236
OfficesNew York · Harrisburg · Seattle
LicensedNY NJ PA MD DE WA OR FL
Rev11.2026
Sheet index