Sprinkler Systems · Comparison
Single vs double interlock preaction: Which one fits?
General guidance, not a code determination for any project. Confirm the adopted code and local amendments with the authority having jurisdiction.
A single interlock preaction system fits heated rooms where the worry is water from a broken pipe or a damaged sprinkler, such as data centers, museums and archives, while a double interlock system fits freezers and other spaces where a false detector alarm must not put water in the pipe either. The difference is what opens the preaction valve: detection alone for single interlock, and detection plus a loss of air or nitrogen pressure from an opened sprinkler for double interlock. That second condition delays the water, so the National Fire Protection Association (NFPA) sprinkler standard, NFPA 13 (2022), gives double interlock the dry pipe penalties: a 30 percent larger design area for density/area designs (Section 19.2.3.2.5) and a cap on system size or water delivery time (Section 8.3.2.3.1).
This article compares the two types side by side, explains why double interlock carries a design penalty, lists the spaces each one usually serves and where each is a poor fit or needs approval, and sets out what the releasing panel has to do. The wider choice among wet, dry, preaction and deluge systems is covered in DGA’s comparison of the four types of sprinkler systems.
At a Glance: Single vs Double Interlock Preaction
- Option A, single interlock: the preaction valve opens when the detection system operates; water fills the pipe and discharges only at a sprinkler that has fused.
- Option B, double interlock: the valve opens only when detection operates and the pipe loses air or nitrogen pressure because a sprinkler has opened; either event alone gives a signal, not water.
- Deciding factor: what water in the pipe at the wrong moment would cost. If a false detector alarm that fills the pipe is tolerable, single interlock; if it is not, as in a freezer where the water would freeze, double interlock.
- When A applies: heated rooms where the piping stays at 40 F or above and the risk is a broken pipe or a damaged sprinkler: data centers, telecommunications and computer rooms, museums, archives and libraries.
- When B applies: freezers and refrigerated rooms kept below 32 F, and rooms where the owner wants neither a false alarm nor a broken pipe alone to admit water; in Delaware, only where the State Fire Marshal specifically accepts it (Regulation 702, Chapter 4, Section 1.3.1.2).
- Cost and complexity direction: double interlock costs more to design and supply: a 30 percent larger density/area design area (NFPA 13 (2022) Section 19.2.3.2.5), a size or delivery limit (Section 8.3.2.3.1) that can mean more valves, and a second release input to maintain. Both types carry the detection, the releasing panel and the annual trip test.
What is the difference between non-interlock, single interlock and double interlock preaction?
A preaction system has closed sprinklers on piping that normally holds air or nitrogen, a preaction valve that keeps water out of that piping, and a separate detection system in the same area that signals the valve to open. NFPA 13 (2022) Section 8.3.2.1 recognizes three preaction types, named for what has to happen before water enters the pipe:
- Non-interlock: water enters when either the detection system or a sprinkler operates. A broken pipe or a knocked-off sprinkler also admits water, so the system works like a dry pipe system with detection added to open the valve sooner.
- Single interlock: water enters when the detection system operates. A sprinkler opening or a pipe breaking with no detection only drops the pipe pressure, which a supervised system reports as a supervisory signal.
- Double interlock: water enters only when the detection system operates and the pipe pressure drops because a sprinkler has opened. Either event alone produces a signal, not water.
The interlock is the condition the releasing panel waits for before it opens the valve. Single interlock guards against water from mechanical damage to the piping; double interlock also guards against a false detector alarm, at the cost of slower water once a fire opens a sprinkler. Non-interlock gives no protection against a broken pipe, so it is not part of the choice this article covers.
Figure 1: What opens the preaction valve
How do single and double interlock preaction systems compare?
The table sets the two types side by side. Section numbers are from NFPA 13 (2022) unless another standard is named.
| Point of comparison | Single interlock | Double interlock |
|---|---|---|
| What opens the valve | The detection system alone | The detection system and a drop in pipe pressure from an opened sprinkler, together |
| Sprinkler knocked off or pipe broken, no fire | Supervisory signal from the pipe pressure; no water | Supervisory signal; no water |
| False detector alarm, no fire | Valve opens and the pipe fills; nothing discharges unless a sprinkler is open; the system is drained and reset | Alarm only; the valve stays shut |
| Water on the fire | Usually already in the pipe when the first sprinkler fuses | Starts moving only after a sprinkler fuses; the gas vents first |
| Density/area design area | No increase | 30 percent larger at the same density (Section 19.2.3.2.5) |
| System size | No more than 1,000 closed sprinklers on one valve (Section 8.3.2.2) | No more than 500 gal, or water at the test connection within 60 seconds, or a calculated delivery time (Section 8.3.2.3.1) |
| Storage sprinklers | Counted as dry in control mode specific application (CMSA) tables (Chapter 22); early suppression fast response (ESFR) only where listed for preaction use (Section 14.2.2) | Same as single interlock |
| Air or nitrogen in the pipe | Supervises the pipe; piping and detection must be supervised on systems with more than 20 sprinklers (Section 8.3.2.4) | Supervises the pipe and is one of the two release conditions |
| Trip test, NFPA 25 (2023) | Every year with the control valve partly open; full flow every 3 years (Section 13.4.3.2.2) | Same schedule |
| Typical spaces | Data centers, telecommunications and computer rooms, museums, archives, libraries | Freezers and refrigerated rooms below 32 F; rooms where neither event alone may admit water |
Every state DGA serves adopts NFPA 13, but the edition differs, and with it some section numbers and details. As of November 2026, New York State and New Jersey use NFPA 13 (2022), Pennsylvania uses the 2019 edition, as do New Jersey applications filed under the prior 2021-based codes through February 17, 2027, and the Delaware State Fire Marshal reviews sprinkler plans to the 2025 edition.
New York City uses NFPA 13 (2016) as modified by Appendix Q of the 2022 New York City Building Code. In Maryland, the county building permit reviews sprinklers to NFPA 13 (2019) through the 2021 International Building Code (IBC), while the State Fire Prevention Code (NFPA 1, 2024) references NFPA 13 (2022).
Why does a double interlock preaction system carry a design penalty?
A double interlock system cannot admit water until a sprinkler has already opened over the fire, so at the moment water is needed the pipe is still full of air or nitrogen. That gas has to vent through the open sprinkler before water arrives, and the fire keeps growing and opening more sprinklers during the delay. A single interlock system avoids most of that delay because its detectors are chosen to respond before the sprinklers, so the pipe is usually full of water when the first sprinkler fuses.
NFPA 13 (2022) treats the delay the way it treats a dry pipe system. Section 19.2.3.2.5 increases the density/area design area by 30 percent, without changing the density, for dry pipe and double interlock preaction systems only. Section 8.3.2.3.1 then caps the size of each double interlock system: it must hold no more than 500 gal, deliver water to the inspector’s test connection within 60 seconds, or meet a delivery time calculated under Section 8.2.3.6, which for high-piled storage means water at 4 open sprinklers within 40 seconds (Table 8.2.3.6.1). A single interlock system is sized by count instead: Section 8.3.2.2 allows no more than 1,000 closed sprinklers on one single interlock or non-interlock valve.
Figure 2: Sequence in a real fire
- A smoke or heat detector operates and the valve opens
- Water fills the pipe while the fire is still small
- The first sprinkler fuses on a pipe already full of water
- Design area as for a wet system, with no 30 percent increase
- A detector operates and the valve stays shut
- The first sprinkler fuses and the pipe pressure drops
- The valve opens, and the gas vents before water arrives
- Design area 30 percent larger; size or delivery time capped
The penalty shows up as flow. If a single interlock design needs 0.20 gallons per minute (gpm) per sq ft over 1,500 sq ft, the design area needs at least 300 gpm; the same room on double interlock needs that density over 1,950 sq ft, or at least 390 gpm, before any hose allowance is added. The extra 90 gpm can mean larger pipe, a larger water service or a fire pump, and the sprinkler hydraulic calculation has to prove the larger area against a current flow test.
Which spaces get single interlock, and which get double interlock?
Single interlock is the usual preaction choice for heated rooms where water from a broken pipe or a damaged sprinkler is the main worry: data centers, telecommunications and computer rooms, museums, archives and libraries. The piping in these rooms can stay at 40 F or above, the temperature NFPA 13 (2022) Section 16.4.1.1 requires for water-filled pipe, so a false detector alarm that fills the pipe costs a drain-down and a reset rather than frozen pipe. For data centers and other mission-critical facilities the point is cost: a discharge from a damaged sprinkler over live equipment can cost as much as a fire.
Double interlock is the usual choice for freezers and refrigerated rooms kept below 32 F. A single interlock system tripped by a false alarm would fill a pipe at freezing temperature with water, and ice in the branch lines can keep the system out of service until it is thawed and drained. DGA’s articles on when cold storage needs preaction sprinklers and what a freezer preaction sprinkler system includes cover the freezer design itself.
Double interlock is sometimes specified outside freezers, for an archive or a data hall where the owner wants neither a false alarm nor a broken pipe alone to admit water. That choice takes on the 30 percent larger design area and the delivery limit, and in Delaware it needs the State Fire Marshal’s specific acceptance. Where the property insurer is FM (formerly FM Global), its Data Sheet 5-32, Data Centers and Related Facilities, sets out the insurer’s own recommendations, which can differ from the NFPA 13 minimum, so the insurer belongs in the decision before the type is fixed.
Figure 3: Choosing between wet pipe, single interlock and double interlock
DGA designs preaction sprinkler systems, and checks preaction designs prepared by others, for data centers, archives and cold storage across New York, New Jersey, Pennsylvania, Maryland, Delaware, Washington, Oregon and Florida. Project briefs get confirmation and preliminary code feedback within one business day. See where DGA works →
Where is each preaction type not permitted or not recommended?
The limits on each type come from sprinkler listings, design rules, the temperature of the space and, in Delaware, a state regulation. The cases below are where each type stops being an option, or stops being a sensible one.
- Double interlock in Delaware: not permitted unless the Office of the State Fire Marshal specifically accepts it (Delaware State Fire Prevention Regulation 702, Chapter 4, Section 1.3.1.2). The State Fire Marshal’s guidance for existing fire sprinkler systems and fire pumps (document 75-01-24-04-06) also requires a formal plan submission before a wet system is converted to preaction.
- Single interlock in a freezer: not recommended, because a false detector alarm fills a pipe below freezing with water that can freeze in place.
- Either type with ESFR sprinklers: not permitted unless the ESFR sprinkler is specifically listed for preaction use (NFPA 13 (2022) Section 14.2.2).
- Either type in CMSA storage designs: permitted only where the CMSA tables give a dry system option, and then counted as a dry system, so single interlock earns no relief from the larger design sprinkler count (Chapter 22).
- Double interlock over a large open floor: can be impractical, because the 500 gal, 60-second or calculated delivery limit in Section 8.3.2.3.1 can split the floor into several systems, each with its own valve, detection zone and trip test.
What does the preaction detection and releasing panel have to do?
The releasing panel is the part of a preaction system that makes the interlock work, and NFPA 72, the National Fire Alarm and Signaling Code, requires the control unit that opens a sprinkler valve to be listed for releasing service (Section 23.11.1). NFPA 13 (2022) Section 8.3.1.2 also requires a manual means of opening the valve that works independently of the detection devices and the sprinklers. The panel’s job is the same for both types; only the release condition changes:
- Watch the detection circuits and, on double interlock, the low air pressure switch on the sprinkler pipe.
- Energize the valve’s releasing device, usually a solenoid, when the release condition is met: detection alone for single interlock, detection plus low pipe pressure for double interlock.
- Supervise the releasing circuit and the pipe pressure, and send alarm, supervisory and trouble signals to the building fire alarm system or the supervising station.
- Allow the detection to be tested without tripping the valve.
The detection type sets how often the panel sees a false alarm, which matters most on single interlock, where every false alarm fills the pipe. The table compares the common inputs.
| Detection or input | What the releasing panel does with it | Code basis | False trip risk |
|---|---|---|---|
| Spot-type smoke detectors | Releases the valve on single interlock, or arms the release on double interlock; releasing designs often require two detectors in alarm first | NFPA 72 Chapter 17 (placement) and Chapter 23 (releasing) | Higher: dust, humidity and construction debris cause nuisance alarms |
| Spot-type heat detectors | Same roles as smoke detectors, but they respond later in a fire | NFPA 72 Chapters 17 and 23 | Lower: needs real heat to operate |
| Air-sampling smoke detection | Gives early warning stages first; the release is tied to a later, higher stage | NFPA 72 Chapters 17 and 23 | Lower at the release stage, set by the threshold chosen |
| Low air pressure switch on the pipe | Supervisory signal on single interlock; the second release condition on double interlock | NFPA 13 (2022) Chapter 8; NFPA 72 Chapter 23 | Not a fire detector: a leak or broken pipe alone never admits water on either type |
The releasing panel follows the NFPA 72 edition each jurisdiction adopts. As of November 2026 that is the 2016 edition as modified by Appendix Q in New York City, 2019 in Pennsylvania and on Maryland county permits through the 2021 IBC (Maryland’s NFPA 1 references the 2022 edition), 2022 in New York State and New Jersey (2019 for New Jersey applications filed under the prior codes), and 2025 in Delaware.
Under NFPA 25 (2023), the inspection and testing standard that Maryland and Delaware reference, both types are trip tested every year with the control valve partly open and with a full flow trip every 3 years (Section 13.4.3.2.2); New York City’s fire code references the 2014 edition. The detection and releasing side is tested under NFPA 72. Because the two halves are designed and tested under different standards, the sprinkler and fire alarm designers should share one sequence of operations that shows the detectors, the releasing device and the pressure switch the same way on both sets of drawings.
Key Takeaway: Single interlock opens the preaction valve on detection alone, keeps the wet-system design area and suits heated rooms where a broken pipe or a damaged sprinkler is the risk. Double interlock waits for detection and a pressure drop from an opened sprinkler, suits freezers, and carries the dry pipe penalties of NFPA 13 (2022): a 30 percent larger design area (Section 19.2.3.2.5) and a size or delivery limit (Section 8.3.2.3.1). Choose by what water in the pipe at the wrong moment would cost, then check the insurer and, in Delaware, the State Fire Marshal’s acceptance.
Frequently asked questions
Does a double interlock preaction system need a larger design area?
Yes, for a density/area design. NFPA 13 (2022) Section 19.2.3.2.5 increases the design area by 30 percent, at the same density, for dry pipe and double interlock preaction systems, while a single interlock system keeps the wet-system area. Control mode specific application (CMSA) storage designs count every preaction system as dry, so both types use the larger dry-system sprinkler count there.
Is a single interlock preaction system designed like a wet system?
Conditional: only for the density/area design area. A single interlock system takes no 30 percent increase under NFPA 13 (2022) Section 19.2.3.2.5, but its pipe is still treated as dry in other ways: black steel pipe takes the lower dry-system Hazen-Williams C-factor in the hydraulic calculation unless a new system uses nitrogen (Table 28.2.4.8.1), the piping is pitched to drain (Section 16.10.3.2), and early suppression fast response (ESFR) sprinklers are allowed only where listed for preaction use (Section 14.2.2).
Can a preaction system protect a freezer?
Yes. Double interlock is the usual freezer choice, because a single interlock system tripped by a false detector alarm would fill a pipe below freezing with water. Freezer systems also follow the NFPA 13 (2022) rules for refrigerated spaces kept below 32 F in Section 8.8, which set the air supply options and other piping details.
Do preaction systems need supervisory air?
Conditional: NFPA 13 (2022) Section 8.3.2.4 requires the piping and the detection devices to be automatically supervised when a preaction system has more than 20 sprinklers, and air or nitrogen pressure in the pipe is the usual way to supervise the piping. A double interlock system needs that pressure to work at all, because a drop in it is one of the two conditions that open the valve.
More in Sprinkler Systems
- What Is NFPA 13? A Plain-English Guide for Owners
- When Does a Sprinkler System Need Seismic Bracing?
- How Do You Size a Water Supply for a 13R or 13D System?
- Do Balconies and Decks Need Sprinklers Under NFPA 13R?
- When Does a Stage or Exhibit Hall Need Special Sprinklers?
- Do Closets, Bathrooms and Small Rooms Need Sprinklers?
This article is general information, not a substitute for a project-specific code analysis. Code editions, local amendments and reviewer practice change; confirm the adopted code and the authority having jurisdiction for the project.
Choosing a Preaction System for a Data Room or Freezer?
Send the room use, the design temperatures, the ceiling plan and the jurisdiction. DGA sets the preaction type and the design basis, prepares the sprinkler drawings and hydraulic calculations, and coordinates the release sequence with the fire alarm design. Project briefs get confirmation and preliminary code feedback within one business day.