Licensed PEs in NY · NJ · PA · MD · DE · WA · OR · FLMon to Fri, 9am to 5pm ET · (646) 355-8274 · info@dgaconsulting.net · Project Desk

Sprinkler Systems · Trigger

When does a dry pipe system need a quick-opening device?

General guidance, not a code determination for any project. Confirm the adopted code and local amendments with the authority having jurisdiction.

A dry pipe sprinkler system needs a quick-opening device only when the design relies on one: to free a system of more than 500 gal, up to 750 gal, from a water delivery time, or to help water reach the far end of the system in time. No system size makes the device mandatory on its own. NFPA 13, the sprinkler installation standard of the National Fire Protection Association (NFPA), sets the rule in Section 8.2.3 of its 2022 edition: outside dwelling units, up to 500 gal a system needs neither a device nor a delivery time, up to 750 gal a listed device removes the delivery time limit, and a larger system must prove how quickly water arrives.

The device is an accelerator or an exhauster on the dry pipe valve trim that trips the valve sooner after a sprinkler opens. This guide covers the capacity steps, the ways to prove delivery time, the alternatives and New Jersey’s 60-second acceptance test.

At a Glance: Quick-Opening Devices on Dry Pipe Systems

  • Threshold(s) with units: system capacity over 500 gal on one dry pipe valve; up to 750 gal with a listed quick-opening device and no delivery time limit; above 750 gal, water at the inspector’s test connection within 60 seconds, or a listed calculation that meets the hazard’s time: 60 seconds for light hazard, 50 for ordinary hazard, 45 for extra hazard and 40 for high-piled storage; a dry system protecting dwelling units must meet 15 seconds at any capacity.
  • Code, edition, section: NFPA 13 (2022) Section 8.2.3 for dry pipe system size and Section 8.2.4 for quick-opening devices, with Table 8.2.3.6.1 for delivery times; the same chapter of the 2019 edition (Pennsylvania, Maryland county permits) and the 2025 edition (Delaware), which renumbers them as Sections 8.2.4.2.1 and 8.2.4.2.2 for size, Table 8.2.4.3.2 for delivery times and Section 8.2.5 for the device; Chapter 7 of NFPA 13 (2016) as modified by Appendix Q in New York City (NYC); NFPA 25 (2023) Section 13.4.5.2.2 for trip tests.
  • Main exceptions: systems of 500 gal or less; systems that meet the 60-second test or a listed calculation without a device; large areas split across more dry pipe valves; cold areas kept on a wet system with heat, dry sprinklers or a listed antifreeze system.
  • What applies once triggered: a listed device close to the dry pipe valve; a listed anti-flooding device unless one is built in; any valve in the device’s connection sealed, locked or supervised open; the device in service for full-flow trip tests; a check for water in the device after every trip.
  • Permit or filing: the designer shows each system’s capacity, the device and any delivery calculation on the sprinkler working plans and hydraulic calculations filed with the authority having jurisdiction (AHJ); in Delaware, converting a wet system to dry needs a formal plan submission to the State Fire Marshal.
  • Who decides: the sprinkler designer sizes each system and picks the delivery route; the AHJ accepts it at plan review and at the acceptance trip test, which in New Jersey must show water at the test pipe within 60 seconds.

What does a quick-opening device do on a dry pipe system?

A dry pipe system keeps air or nitrogen under pressure in the piping, and a dry pipe valve in a heated room holds the water supply back until a sprinkler opens. In a differential dry pipe valve the air acts on a larger area of the clapper than the water does, so a modest air pressure holds back a much higher water pressure. DGA’s comparison of wet, dry, preaction and deluge systems covers when a space needs a dry system in the first place.

The time to water has two parts. When a sprinkler opens, air bleeds out until the pressure falls to the valve’s trip point, and only then does water start to fill the empty pipe toward the open sprinkler. A quick-opening device shortens the first part by tripping the valve sooner, but the water still has to travel through the empty pipe, which is why NFPA 13 still caps a system with a device at 750 gal unless its delivery time is proven.

Most quick-opening devices use two chambers with a diaphragm between them, as FM Approvals describes in its Class 1031 approval standard (August 2019). A restriction orifice lets slow pressure changes, such as a compressor cycling, equalize across the diaphragm, while the faster drop from an open sprinkler moves it and sets the device off. The two types, accelerators and exhausters, differ in how they then open the valve, as compared below.

When does NFPA 13 require a quick-opening device?

NFPA 13 (2022) Section 8.2.3 ties the device to capacity without requiring it at any size: a dry pipe valve that controls more than 500 gal of piping either gets a listed quick-opening device and stays within 750 gal, or proves its water delivery time, and Section 8.2.4 permits a device to help meet that time. Capacity is counted per dry pipe valve, so two valves serving two halves of a building are two systems with two separate totals. The table sets out each step and its basis.

ConditionRuleBasis
Capacity of 500 gal or lessNo quick-opening device and no water delivery time limit, except in dwelling unitsNFPA 13 (2022) Section 8.2.3.3
Capacity over 500 gal, up to 750 galA listed quick-opening device, with no delivery time limit; or no device where the 60-second test or a listed calculation proves the delivery time without oneNFPA 13 (2022) Chapter 8
Capacity over 750 galDelivery time proven by the 60-second test, or by a listed calculation or a manifold test connection against the hazard’s limit; a quick-opening device is permitted to help meet that timeNFPA 13 (2022) Sections 8.2.3.2, 8.2.3.5 to 8.2.3.7 and 8.2.4.1; Table 8.2.3.6.1
Dry pipe system protecting dwelling unitsWater delivery within 15 seconds at any capacity; the 500 gal, 750 gal and 60-second options do not applyNFPA 13 (2022) Sections 8.2.3.1.1 and 8.2.3.1.1.1
Double interlock preaction systemUp to 500 gal with no delivery time limit, a 60-second delivery to the test connection, or a calculated delivery time; no 750 gal step for a quick-opening deviceNFPA 13 (2022) Section 8.3.2.3.1
Any dry pipe system in New JerseyWater at the inspector’s test pipe within 60 seconds at the acceptance test, whatever the capacityInternational Building Code (IBC) Section 903.5.1 as amended in New Jersey Administrative Code (N.J.A.C.) 5:23-3.14(b)8

Double interlock preaction systems follow a parallel rule because water cannot enter the piping until both detection and an opened sprinkler release it. DGA’s guide to when cold storage needs preaction sprinklers covers where those systems fit.

Figure 1: Dry pipe system capacity and the quick-opening device

  1. 3Over 750 gal: delivery time must be provenThe 60-second test or a listed calculation against Table 8.2.3.6.1; a device may help meet the time
  2. 2Over 500 gal, up to 750 gal: a device or a proven delivery timeA listed quick-opening device removes the delivery time limit
  3. 1500 gal or less: no device and no delivery timeNFPA 13 sets no water delivery requirement at this size outside dwelling units
Under NFPA 13 (2022) Chapter 8, a dry pipe system of up to 500 gal outside dwelling units needs no quick-opening device and no delivery time, a system of up to 750 gal needs no delivery time once it has a listed device, and a larger system must prove its delivery time by the 60-second test or a listed calculation. New Jersey adds a 60-second limit at the inspector’s test pipe for every dry pipe system at acceptance.

As of November 2026, these rules apply under NFPA 13 (2022) in New York State and New Jersey, NFPA 13 (2019) in Pennsylvania through the 2021 IBC and NFPA 13 (2025) in Delaware under Regulation 701 of the State Fire Prevention Regulations; New Jersey applications filed under the prior 2021-based codes through February 17, 2027 stay on the 2019 edition. In Maryland, the county building permit reviews sprinklers to NFPA 13 (2019) through the 2021 IBC, while the State Fire Prevention Code (NFPA 1, 2024) references NFPA 13 (2022). NYC uses NFPA 13 (2016) as modified by Appendix Q of the 2022 NYC Building Code, where the dry pipe rules sit in Chapter 7; Appendix Q Section Q102 leaves the capacity and quick-opening device rules as published and adds a supervisory signal for high or low system air pressure.

How is a dry pipe system’s capacity measured?

Capacity is the volume of every pipe on the system side of the dry pipe valve: the riser above the valve, the feed and cross mains, the branch lines and any drops or sprigs. The designer totals it from the pipe takeoff on the working plans, run by run, using each pipe’s actual inside diameter rather than its nominal size. Fittings add a little more, and the total is rechecked whenever the system is extended.

Figure 2: Dry pipe system capacity from the pipe takeoff

Capacity of one pipe run: V = 0.0408 × d2 × L, where V is in gallons, d is the actual inside diameter in inches and L is the length in ft. The factor 0.0408 is π ÷ 4 × 12 ÷ 231, which turns the cubic inches in a foot of pipe into gallons.

System capacity: the sum of V for every run on the system side of the dry pipe valve, compared with the 500 gal and 750 gal steps.

Gallons per ft used in the example: 4-inch Schedule 10 (4.260-inch bore) 0.740; 1-1/2-inch Schedule 40 (1.610-inch bore) 0.106; 1-1/4-inch Schedule 40 (1.380-inch bore) 0.078; 1-inch Schedule 40 (1.049-inch bore) 0.045.

A foot of 4-inch Schedule 10 pipe holds 0.740 gal against 0.661 gal for 4-inch Schedule 40, because the thinner wall leaves a larger bore. In the one-level garage example, 300 ft of 4-inch main holds 222.0 of the system’s 415.3 gal.

The worked example is a dry pipe system on one level of an unheated parking garage. Its takeoff totals 415.3 gal, under the 500 gal step, so the system needs no quick-opening device and has no delivery time to meet under NFPA 13.

Pipe on the system side of the valveLengthGallons per ftGallons
4-inch Schedule 10 riser, feed main and cross main300 ft0.740222.0
1-1/2-inch Schedule 40 branch lines1,000 ft0.106106.0
1-1/4-inch Schedule 40 branch lines600 ft0.07846.8
1-inch Schedule 40 branch line ends900 ft0.04540.5
One garage level on one dry pipe valve2,800 ft415.3

Growth changes the answer. Extending the same system across a second bay adds 150 ft of 4-inch main, 500 ft of 1-1/2-inch, 300 ft of 1-1/4-inch and 440 ft of 1-inch pipe, or 207.2 gal, for 622.5 gal in all, so the valve now needs a quick-opening device or a proven delivery time. Feeding a whole second level from the same valve doubles the first takeoff to 830.6 gal, above 750 gal, where the delivery time has to be proven by test or calculation.

How is water delivery time shown: By calculation, by test or by system volume?

NFPA 13 (2022) Chapter 8 gives three ways to size a dry pipe system. The volume route relies on the 500 gal and 750 gal steps alone and needs only an accurate capacity total, while the test and calculation routes let a system grow larger by proving that water arrives in time.

The test route is the traditional one. With the system at its normal air pressure, the inspector’s test connection at the far end is opened fully, and water must flow from it within 60 seconds; a listed quick-opening device may be used to make the time.

The calculation route uses a water delivery program listed by a nationally recognized testing laboratory, which models the valve trip, the air bleeding out and the water filling the pipe to the most remote sprinklers. NFPA 13 (2022) Table 8.2.3.6.1 sets the limit by hazard, pairing the number of most remote sprinklers assumed open, from 1 to 4, with the longest time allowed for water to reach them, from 15 seconds for dwelling units to 60 seconds for light hazard. High-piled storage, for example, assumes 4 sprinklers open and allows 40 seconds, and double interlock preaction systems sized by calculation use the same limits (Section 8.3.2.3.1). A trip test through a manifold test connection can also show those times (Section 8.2.3.7).

Whichever route the design used, the acceptance trip test opens the test connection and times the water, and the result is recorded on the contractor’s material and test certificate. New Jersey puts a fixed limit on that test: under its amendment to IBC Section 903.5.1, every dry pipe system must deliver water to the inspector’s test pipe in not more than 60 seconds, so a system NFPA 13 would size by volume alone still has to make 60 seconds there.

Opens the Project Desk with your sentence. Our licensed PEs review every brief and reply within one business day.

Which dry pipe systems can do without the device?

Small systems are the first group. A dry pipe system of 500 gal or less needs no quick-opening device under NFPA 13 (2022) Chapter 8, a size that small unheated areas such as a loading dock, a canopy or an attic often stay within when each has its own valve.

Larger systems can skip the device when they meet the delivery time without one, and that time depends on how much air has to bleed out and how far water has to travel. A compact layout with the riser close to the remote area, or a lower air pressure within what the dry pipe valve’s listing allows, shortens it. Splitting a large unheated area across more dry pipe valves keeps each system small, at the cost of more valves, heated valve enclosures and trip tests.

The broadest alternative is to avoid a dry system. NFPA 13 (2022) Section 16.4.1.1 allows water-filled piping wherever it is kept at 40 F or above, and dry sprinklers fed from heated piping (Section 15.3), listed heat tracing or a listed antifreeze system (Sections 16.4.1.2 and 16.4.1.4) can cover a small cold area, as DGA’s guides to antifreeze sprinkler systems and freeze protection for parking garage sprinklers explain. Staying wet also avoids the 30 percent larger design area that Section 19.2.3.2.5 applies to dry pipe systems under the density/area method.

Local rules can push the same way. In Montgomery County, Maryland, the Department of Permitting Services (DPS) NFPA 13 submittal requirements accept a dry pipe system only where heat cannot keep the space from freezing. In Delaware, the State Fire Marshal’s guidance for existing systems requires a formal plan submission to convert a wet system to dry, or the reverse, so the choice is best settled at design.

What applies once a quick-opening device is installed?

A quick-opening device brings installation rules in NFPA 13 (2022) Chapter 8, acceptance tests in Chapter 29 and recurring trip tests under NFPA 25 (2023), the inspection, testing and maintenance standard for water-based systems. The table lists the installation and acceptance items and their sources.

ItemWhat it requiresBasis
Listing and locationA listed quick-opening device, as close as practical to the dry pipe valve, installed in the valve trim the manufacturer showsNFPA 13 (2022) Chapter 8; manufacturer’s trim chart
Connection to the riserAbove the priming water level of the dry pipe valveNFPA 13 (2022) Chapter 8
Valve in the connectionIndicating type, sealed, locked or electrically supervised openNFPA 13 (2022) Chapter 8
Anti-floodingA listed anti-flooding device between the riser and the quick-opening device, unless the device has anti-flooding features built in or is listed for use without oneNFPA 13 (2022) Section 8.2.4.8; FM Approvals Class 1031
AcceptanceAn air test at 40 psi for 24 hours, losing no more than 1.5 psi, on top of the hydrostatic test; then a trip test with the time to water recorded, within 60 seconds in New JerseyNFPA 13 (2022) Sections 29.2.1.1, 29.2.2.1 and 29.2.3.2; N.J.A.C. 5:23-3.14(b)8

The anti-flooding rule protects the device from its own system. Under FM Approvals’ Class 1031 standard, an anti-flooding device must keep water and debris out of a mechanical accelerator, whose small internal orifices can clog. Some accelerators build the protection in: Viking’s Model D-2 accelerator carries an integral anti-flood assembly and is FM Approved as an accelerator with a built-in anti-flooding device.

Upkeep follows from the same small passages. After any operation, Viking’s instructions call for checking the accelerator for water and, where water or dampness is found, taking it apart, cleaning and drying it before the system returns to service, with its isolation valves kept open. In NYC, Appendix Q also requires a supervisory signal whenever the air pressure in a dry pipe system runs high or low.

The device stays part of the valve for life. NFPA 25 (2023) Section 13.4.5.2.2, the edition Delaware adopts and Maryland’s fire code references, requires a trip test of each dry pipe valve every year and a full-flow trip test every 3 years and after alterations, run with any quick-opening device in service (Section 13.4.5.2.2.2). NYC adds its own schedule in Fire Code Section 903.6: a trip test at least once every 5 years and whenever the system is altered, with the control valve fully open and the device in service, run by a master fire suppression contractor licensed by the Department of Buildings (DOB) before a Fire Department of the City of New York (FDNY) representative.

How do accelerators and exhausters differ?

Accelerators and exhausters are both quick-opening devices, and both trip on a sustained drop in system air pressure; the difference is where the air goes. An accelerator redirects system air into the dry pipe valve’s intermediate chamber, which cancels the pressure balance across the clapper and opens the valve. An exhauster vents system air to the atmosphere, so the pressure reaches the valve’s own trip point sooner (FM Approvals Class 1031).

NFPA 13 (2022) Chapter 8 treats the two alike: either type counts as a listed quick-opening device, and the same capacity steps and installation rules apply. Viking’s current Model D-2, for example, is an accelerator installed in the dry valve trim according to its trim chart, and it resets on its own once its gauge reads zero.

Key Takeaway: No system size makes a quick-opening device mandatory: a dry pipe system needs one only when the design relies on it, to free a system of more than 500 gal, up to 750 gal, from a water delivery time or to help water reach the remote end in time (NFPA 13 (2022) Sections 8.2.3 and 8.2.4). Up to 750 gal the device removes any delivery time limit; above 750 gal the delivery time must be proven against limits of 15 to 60 seconds set by hazard. New Jersey holds every dry pipe system to 60 seconds at the inspector’s test pipe, and NYC adds an FDNY-witnessed trip test every 5 years with the device in service.

Frequently asked questions

Do all dry pipe systems need an accelerator?

No. NFPA 13 (2022) sets no system size that requires a quick-opening device, an accelerator or an exhauster: a system needs one only when the design relies on it, to free a system of more than 500 gal, up to 750 gal, from a water delivery time or to help water reach the remote end in time (Sections 8.2.3 and 8.2.4). New Jersey still requires every dry pipe system, whatever its size, to deliver water to the inspector’s test pipe within 60 seconds at acceptance (N.J.A.C. 5:23-3.14(b)8).

What is the maximum water delivery time for a dry system?

60 seconds is the longest NFPA 13 (2022) allows where a delivery time applies: 60 seconds at the inspector’s test connection on the test route, or the hazard’s limit on the calculation route. Table 8.2.3.6.1 sets those limits at 15 seconds for dwelling units, 60 for light hazard, 50 for ordinary hazard, 45 for extra hazard and 40 for high-piled storage, with 1 to 4 remote sprinklers assumed open. Outside dwelling units, a system of 500 gal or less, or 750 gal or less with a quick-opening device, has no delivery time under NFPA 13, though New Jersey holds every dry pipe system to 60 seconds.

Can a dry pipe system hold more than 750 gallons?

Yes. NFPA 13 (2022) Chapter 8 sets no gallon limit above 750 gal for a system that proves its water delivery, either with water reaching the inspector’s test connection within 60 seconds or with a listed calculation that meets the time for its hazard. A listed quick-opening device may be added to help meet that time. Splitting a large area across more dry pipe valves is the other way to keep each system within the limits.

How often is a dry pipe valve trip tested?

Every year, with a full-flow trip test every 3 years, under NFPA 25 (2023) Section 13.4.5.2.2. In NYC, Fire Code Section 903.6 also requires a trip test at least once every 5 years and whenever the system is altered, with the control valve fully open and any quick-opening device in service, in the presence of an FDNY representative.

This article is general information, not a substitute for a project-specific code analysis. Code editions, local amendments and reviewer practice change; confirm the adopted code and the authority having jurisdiction for each project.

Sizing a Dry Pipe System for an Unheated Space?

Send the floor plans, the space temperatures, the hazard and the jurisdiction. DGA lays out the dry pipe systems, totals each one’s capacity and shows whether a quick-opening device or a delivery calculation is needed. Project briefs get confirmation and preliminary code feedback within one business day.

Send a project brief → View related services

Leave a reply

Your email address will not be published. Required fields are marked *

Quick inquiry

Ready when you are.

Your name, a way to reach you, and where the project is. A licensed PE replies within one business day. Every inquiry is confidential.

Prefer to describe it first? Open the Project Desk

FirmDGA Fire Protection Engineering
SheetFP-5219
OfficesNew York · Harrisburg · Seattle
LicensedNY NJ PA MD DE WA OR FL
Rev11.2026
Sheet index